Amps
[Top] [All Lists]

[AMPS] Re: Alpha H.V. Rectifier Source

To: <amps@contesting.com>
Subject: [AMPS] Re: Alpha H.V. Rectifier Source
From: paulc@mediaone.net (Paul Christensen)
Date: Sat, 5 Sep 1998 19:22:39 -0400
I should have conducted a web search first.  SEMTECH continues to offer the
original SCH5000 H.V. rectifiers factory-direct and through distributors.
Anyone wanting to know the exact specifications of these diodes used in
older Alpha amplifiers can find it here:

http://www.semtech.com/pdf/rectifier/halfwave/schx.pdf

I'll plan on first checking with Alpha/Power for stock on Tuesday.  Thanks
to everyone for their replies!

-Paul, W9AC

-----Original Message-----
From: Paul Christensen <paulc@mediaone.net>
To: amps@contesting.com <amps@contesting.com>
To: <amps@contesting.com>
Date: Saturday, September 05, 1998 2:36 PM
Subject: Alpha H.V. Rectifier Source


>In my continued pursuit of finalizing my Alpha PA-70V rebuild, I discovered
>that a nylon H.V. feedthrough jack between the power supply and R.F.
cabinet
>is causing my H.V. flashover, not the 3CV1500A7 as I originally suspected.
>In place of the nylon feedthrough, is now a glazed-porcelain James Millen
>"beehive" type, which I filled with 100% silicone clear RTV.  If this
>doesn't take care of 4KV leaking to ground, I give up.
>
>I also noted that upon my last flashover, my glitch protection circuitry
did
>its job: I replaced a string of three 1N5408 diodes, not the plate ammeter.
>Unfortunately, a 50-ohm @ 50-watt H.V. lead resistor I recently installed
is
>AFTER the feedthrough.  However, another failure occurred.  One of the four
>H.V. diode "blocks" is shorted.   It is marked...
>
>SEMTECH  "SLIMPAC"
>SCH 5000
>
>Does anyone know if Alpha/Power is still carrying these?  I believe my 77Dx
>used the same type.  If I cannot obtain an exact replacement through a web
>search, would it be prudent to simply replace all four with a newer type?
>Does the "infamous" K2AW Silicon Alley have these?  I measured the forward
>and reverse resistance of the remaining three H.V. "blocks" and they all
>measure identical.  Is it safe to assume that they are not on the ragged
>edge of failure?
>
>In my search for a spare vapor-cooled 3CV1500A7, I not only found one
>new-in-the-box, but I also "coerced" the seller into letting me purchase
his
>new Alpha PA-70V which is in its original box with only a few hours on it.
>This is one of the few times when I really got lucky!
>
>To be safe, I'll probably change out the H.V. feedthrough, H.V. wiring and
>perhaps upgrade the plumbing as I had recently done using all Teflon
>components.  Does anyone know the life expectancy of 20KV silicon rubber
>high voltage wire?
>
>-Paul, W9AC
>
>


--
FAQ on WWW:               http://www.contesting.com/ampfaq.html
Submissions:              amps@contesting.com
Administrative requests:  amps-REQUEST@contesting.com
Problems:                 owner-amps@contesting.com
Search:                   http://www.contesting.com/km9p/search.htm


<Prev in Thread] Current Thread [Next in Thread>
  • [AMPS] Re: Alpha H.V. Rectifier Source, Paul Christensen <=