Amps
[Top] [All Lists]

Re: [Amps] W3NQN band pass filters

To: <d.cutter@ntlworld.com>, "Alton McConnell Avon-Cadillac" <amcconnell@avonauto.com>, <amps@contesting.com>
Subject: Re: [Amps] W3NQN band pass filters
From: "jeremy-ca" <km1h@jeremy.mv.com>
Date: Fri, 13 Jun 2008 13:53:27 -0400
List-post: <amps@contesting.com">mailto:amps@contesting.com>
Even the best of filters will sometimes be insufficient in a contest 
enviroment.

I augmented my filters with coax stubs in the feedline to pick up another 
20-25 dB. Some were cut for CW and SSB segments and changed as needed.

Carl
KM1H


----- Original Message ----- 
From: <d.cutter@ntlworld.com>
To: "jeremy-ca" <km1h@jeremy.mv.com>; "Alton McConnell Avon-Cadillac" 
<amcconnell@avonauto.com>; <amps@contesting.com>
Sent: Friday, June 13, 2008 8:03 AM
Subject: Re: Re: [Amps] W3NQN band pass filters


> Presumably this is for a contest station.  What matters more is the break 
> thro into the other station's rx and this can be strongly influenced by 
> the antenna or input Z of the linear on the filter.  It's particularly a 
> problem on a wide band like 80m
>
> Breakthro into an adjacent filter is important, so  a rigorous approach to 
> screening and relay switching is needed.  I think it was the Bavarian 
> Contest Group that showed a multi-filter bank you will find interesting
>
> David
> G3UNA
>
>>
>> From: "jeremy-ca" <km1h@jeremy.mv.com>
>> Date: 2008/06/11 Wed PM 04:52:33 BST
>> To: "Alton McConnell  Avon-Cadillac" <amcconnell@avonauto.com>,
>> <amps@contesting.com>
>> Subject: Re: [Amps] W3NQN  band pass filters
>>
>> A 1.2:1 VSWR isnt sufficient?
>>
>> Carl
>> KM1H
>>
>>
>> ----- Original Message ----- 
>> From: "Alton McConnell Avon-Cadillac" <amcconnell@avonauto.com>
>> To: <amps@contesting.com>
>> Sent: Monday, June 09, 2008 8:03 AM
>> Subject: [Amps] W3NQN band pass filters
>>
>>
>> >I am trying to align some W3NQN band pass filters that I have built for
>> > club use. I am using the design from the May and June 1998 QST article.
>> >
>> > I am using a HP 8656 Signal generator and a 30 MHz scope for the 
>> > tuning.
>> > Measuring the return loss with a MFJ 269 SWR analyzer, the best that I
>> > can do is 20db.
>> >
>> > Any suggestions for alignment of the filters?
>> >
>> > Alton, NU8L
>> > Amcconnell3@hotmail.com
>> >
>> >
>> > This e-mail and any files transmitted with it are the property of Avon
>> > Automotive, are confidential, and are intended solely for the use of 
>> > the
>> > individual or entity to whom this e-mail is addressed. If you are not 
>> > one
>> > of the named recipients or otherwise have reason to believe that you 
>> > have
>> > received this e-mail in error, please notify the sender and delete this
>> > message immediately. Any other use, retention, dissemination, 
>> > forwarding,
>> > printing or copying of this e-mail is strictly prohibited.
>> >
>> > The views, opinions, conclusions and other informations expressed in 
>> > this
>> > electronic mail are neither given nor endorsed by Avon Automotive 
>> > unless
>> > otherwise indicated by an authorized representative independent of this
>> > message.
>> >
>> >
>> > This message has been scanned for malware by SurfControl plc.
>> > www.surfcontrol.com
>> > _______________________________________________
>> > Amps mailing list
>> > Amps@contesting.com
>> > http://lists.contesting.com/mailman/listinfo/amps
>> >
>>
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>>
>
> -----------------------------------------
> Email sent from www.virginmedia.com/email
> Virus-checked using McAfee(R) Software and scanned for spam
>
> 

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>