On 11/22/2011 9:59 PM, Ken wrote:
> Now..now...A sweep tube amp was the first amp I ever built....Most of the
> parts came out of two TV sets and the rest I got out of an old AM
> radio...Hummm I've still got that thing somewhere.
I guess I couldn't call my first transmitter an amp, but it did use a
pair of 6L6's in the final.
6AG7 driving a pair of 6L6's built on an old TV chassis. I kept the TV
power supply which took up one
corner of the chassis and the transmitter another. I used a 12AT7 as a
TR switch so I was operating QSK
as a novice. It was big, ugly, had lots of sharp corners and
projections, but it worked...after I discovered
most of the resistors I had used were wire wound. Replacing them with
carbon composition worked wonders!<:-))
All those sharp corners kept it from sliding off tables too. As much as
it weighed with that big steel chassis
I doubt slipping would have been much of a problem without the sharp
corners.
Then there was the little Dentron GLA-1000B which used a passel of sweep
tubes. (6 IIRC) It wasn't that great an amp
but it did work. I drove it with the little Kenwood solid state rig back
around 1980. I forget the model number
other than I think it ended in a "30". Rig was only 3 or 4 inches high.
Twas a little larger than the current
Icom 7000.
73
Roger (K8RI)
> Ken
> N4zed
>
>
> ----- Original Message -----
> From: "Carl"<km1h@jeremy.mv.com>
> To:<dhallam@knology.net>; "Amps reflector"<amps@contesting.com>
> Sent: Tuesday, November 22, 2011 8:21 PM
> Subject: Re: [Amps] Sweep Tube Amps
>
>
>> You should probably ask that on one of the CB amp forums....seriously.They
>> should have more experience and at least you may get a good laugh.
>>
>> Carl
>> KM1H
>>
>>
>> ----- Original Message -----
>> From: "David C. Hallam"<dhallam@knology.net>
>> To: "Amps reflector"<amps@contesting.com>
>> Sent: Tuesday, November 22, 2011 5:25 PM
>> Subject: [Amps] Sweep Tube Amps
>>
>>
>>> First of all, don't tell me to get a real amplifier. I have other
>>> "real" amps.
>>>
>>> My question is: 3 sweep tube types are stated to be equivalent, 6JE6,
>>> 6LQ6, and 6ML6. Are they really interchangeable in a set, i.e., can I
>>> mix the 3 types in a set of 6? The amp has no way to equalize the idle
>>> current.
>>>
>>> I have built multi tube amps before, 4CX300A, but included separate bias
>>> adjustment pots for each tube. I have no intention of building a sweep
>>> tube amp.
>>>
>>> David
>>> KW4DH
>>>
>>> --
>>> "I predict future happiness for Americans if they can prevent the
>>> government from wasting the labors of the people under the pretense of
>>> taking care of them."
>>> Thomas Jefferson
>>>
>>>
>>> "We may consider each generation as a distinct nation, with a right, by
>>> the will of its majority, to bind themselves, but none to bind the
>>> succeeding generation, more than the inhabitants of another country."
>>> Thomas Jefferson
>>>
>>>
>>> _______________________________________________
>>> Amps mailing list
>>> Amps@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/amps
>>>
>>>
>>> -----
>>> No virus found in this message.
>>> Checked by AVG - www.avg.com
>>> Version: 10.0.1411 / Virus Database: 2092/4032 - Release Date: 11/22/11
>>>
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|