Just because "they all do it" doesn't make it right.
## No its not. Alpha did the same for years..at least a long tine ago on
their
-----Original Message-----
From: Larry <lknain@nc.rr.com>
To: amps <amps@contesting.com>
Sent: Thu, Sep 12, 2013 7:09 am
Subject: Re: [Amps] Clipperton-L question
The amp groans quite a bit when first powered on of course. I never noticed
any surge in the sense of "groaning" or lights dimming when going from CW to
SSB. That doesn't mean it's not there just something I never noticed and
certainly not as obvious as a power on.
73, Larry W6NWS
-----Original Message-----
From: Jim Thomson
Sent: Thursday, September 12, 2013 12:58 AM
To: amps@contesting.com
Subject: [Amps] Clipperton-L question
Date: Wed, 11 Sep 2013 18:37:25 -0700
From: Richard Solomon <dickw1ksz@gmail.com>
To: "amps@contesting.com" <amps@contesting.com>
Subject: Re: [Amps] Clipperton-L question
I actually had to check the schematic ... I couldn't believe they switch
the
HV side of the Xfmr, but they do.
That's a terrible design.
73, Dick, W1KSZ
## No its not. Alpha did the same for years..at least a long tine ago on
their
smaller desk top amps. They used an OPTIONAL $80.00 spdt vac relay
to do the job. Of course nobody bought the optional vac relay...and just
wired it
permanently in the SSB-higher B+ position.
## The real trick is that when you switch from CW to SSB, your typ step
start circuit
is non-functional..and u get one helluva surge. On my HB B+ supply, with
the 253 lb
Dahl xfmr, I use a multi-tech industries model 88 switch, 13 kv rated, to
change the various HV sec taps.
Even then, I have to 1st shut off the 240 vac primary, then change the sec
taps, then turn the B+ supply
back on. Then it goes through its normal step start sequence.
## Now if going from a higher B+ to a lower B+... there is no need to
shut off the supply. I have loads
of sec taps on the big dahl xfmr...and all that is required is to grab ANY
two sec taps. IE: Its tapped at
0-2300-3900-4800-5200 vac. Since I don’t have a 2900 tap... what I do is
use the 5200 + 2300 taps.
5200-2300 = 2900 vac. Problem solved. To pull that off I used a 2nd
model 88 switch. On switch
is wired to half the sec taps...and the 2nd switch is wired to the other
half of the sec taps.
## On my other HB B+ supply, that uses a 10 kva, 4800 vac pole pig
xfmr... I used a
DPDT relay....with all contacts in parallel, to handle more current.... to
toggle between
one hot leg of the 240 line...and neutral. That way I can stuff either
120 OR 240 vac into the
240 vac primary. That results in either the full 6800 vdc... or 3400
vdc.
## To get around the step start issue, I used a SPDT- CENTER OFF type of
toggle switch to
switch back and forth between 6800-3400 and 3400-6800. When passing
through the CENTER OFF
middle position of the SPDT toggle, the step start timer drops out, and
also the big relay that
does the actual shunting of the step start resistors. That way, whether it
switchs from low to high,
or from\high to low, the step start circuit always does its thing. I used
the spare set of contacts
on the dpdt 0-15 sec timer module, to run the amp key line in and out of.
That way, during the 15 sec
step start sequence, the amp cant be keyed.
Later... Jim VE7RF
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|