Amps
[Top] [All Lists]

[Amps] Question about grid current in 4CX or 3CX

To: <amps@contesting.com>
Subject: [Amps] Question about grid current in 4CX or 3CX
From: "Jim Thomson" <jim.thom@telus.net>
Date: Sat, 16 Mar 2019 09:55:49 -0700
List-post: <mailto:amps@contesting.com>
Date: Fri, 15 Mar 2019 10:37:37 -0500
From: donroden@hiwaay.net
To: amps@contesting.com
Subject: [Amps] Question about grid current in 4CX or 3CX

<Question

<For the larger tubes with handles  ( commercial service )

<Does grid current increase or decrease as plate voltage and screen  
<voltage is removed. ?

<If it takes 250 watts to produce 100ma of grid current in a 4CX10,000.
<is the grid just a big dummy load and is it doing the tube harm to  
<dump 250 watts into it when both plate and screen voltages are removed ?


<Don W4DNR

##  I am assuming in the case of the  3CX  series,   that the grid is bonded to 
chassis
via the  GG socket..and tube is cathode  driven.... just like any GG triode. 

##    I am assuming the  4CX  tetrode is being grid driven,  with the usual  
screen  and  B+
voltages applied. 

##  In the case of the  GG triode, and no B+... but drive still applied, you 
will send the  grid
current through the roof !   Without any B+, the  tube now thinks the control 
grid is the anode.
All the  electrons  will flow from directly heated cathode to the  control 
grid.   I have verified this
several times on  several different triodes, including the  larger metal types. 
  Thats why I  install
a  rear panel  3AGC  fuse holder, and wire it between  chassis....and  the 
negative terminal of the
dc grid meter.  Then use a FAST fuse, thats  barely rated for normal average  
dc grid current. 

## If you lose the B+,  and dc grid current skyrockets,   grid fuse blows open 
asap.  With  NO  path
for dc grid current, triode can not be driven.  Power  output drops to ZERO.   
Input  swr, between 
xcvr and  input to the GG triode amp  rises to infinity.   Xcvr then shuts 
itself  down asap.   Event over. 

##  On GG triodes, with delicate 4 watt grids, like the  3CX-800A7,  and loss 
of B+,  whats then required
is high speed electronic grid over current protection.  Another method  is if  
B+   falls below a certain threshold,say 
less than  70%  of normal,  amp kicks off line asap.   For  GG triodes like  
3-500Z,  3x3, 3x6,  3x10, 3x15   etc, the
grid fuse is ample. 

##  IF the tetrode is run like a high mu  triode, with both screen grid and 
control grid  bonded to  chassis,
use the grid fuse method.    This config requires a lot of drive...like  625  
watts.   Back in the day, a SB-220,
run in the  CW position was used for  the ipa. 

##  IF the tetrode is grid driven, with the usual  screen and  B+ applied, and  
the typ  450 ohm globar used to 
derive grid voltage..when driven  through the  typ 1: 9  un-un......and screen 
and  B+  are simultaneously 
removed... I THINK the  globar just dissipates the normal drive power.   But  
dunno if the  dc grid current increases
or not.  On the  grid driven tetrode, run in passive grid with the 1:9  un-un  
and 450 ohm globar, the  dc grid  current
is typ 0 ma... if tube run in  class  AB1.     Typ the  4CX-10,000A7, when grid 
driven In the passive grid config, 
only requires  130 watts  for 14 kw pep output.   You would never require  250 
watts. 

##  On tetrodes like the  4CX-1000  variety, complete  with their  ZERO watt 
grid  diss rating, grid over current is 
required, and will kick amp offline with  just  100  microamps of  grid 
current. 

##  Then u can also get into goofy configs with the same tetrode, like just 
loss of  screen voltage.... or   just loss
of  B+.   On the commercial tetrode amps, like collins  208-U  series and 
similar  from others like aerocom, etc
they all had  plate over current, screen overcurrent,and grid over current 
relays and protection built in..and all 3
have adjustable thresholds.

Later... Jim   VE7RF

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>