Andy,
You can use the same delay lines and phase angles with the 4 Square,
but you have to make the length of the diagonal equal to the 80m
spacing between elements 1 and 3 in the linear endfire array. (So
the spacing between adjacent elements is 1.414 * 40m.) This gives
30 dB back lobes, but the azimuth pattern is quite different, with
two fairly large lowangle sidelobes (12 dB at +/ 114 degrees at
0.53 and 1.06 MHz). Even though this looks like a poorer pattern
than the 3 element inline array, the 4 square has a narrower main
lobe and an RDF that is 1 dB higher, because of deep nulls at +/ 78
degrees that aren't present with the 3 element array.
The back lobes of both the 3 element and the 4 square grow with
increasing frequency until they are about 22 dB at 2.65 MHz. The 3
element main lobe gets quite broad in azimuth (157 degrees) and is
down about 0.5 dB on boresight. With the 4 square, the main lobe is
just 73 degrees wide, however those pesky sidelobes are only 5
dB. The RDF of the 4 square is about 2 dB higher at 2.65 MHz.
Life is all about compromise, eh?
73, Terry N6RY
At 04:39 AM 20080910, Andrew Ikin wrote:
>Many thanks Chris and Ken for your responce to mail below:
>
>I trust that a brief description of the array will answer your questions.
>
>The proposed antennas will be receive only 12m active Vertical (
>FET/Bipolar buffer amp) hence there will be no element mutual
>interaction. The centre element is run in antiphase compared to the
>outer elements, the amplitude is the sum of the outer elements also.
>All 3 elements are combined using zero delay for Element
>1; 0.73x40m (95ns) for the centre (2) Element and 0.73x80m (190ns)
>for the Element 3.
>
>The delaylines provide near optimum phasing for reduced rear
>vertical lobe from 0.53MHz to 2.65MHz. Going above 2.65MHz or
>0.35Lambda spacing the Gain and F/B starts to reduce.
>
>The array was modelled at 0.53,1.06,1.59, 2.12 and 2.65MHz using the
>degrees phasing calculated from the delaylines i.e. the correct
>phasing tracks the frequency range.
>
>Eg. for 0.53MHz the phasing is 0, 162, 324 degrees and for 1.06MHz
>the phasing 0, 143, 286 degrees. The delaylines were determined
>from a similar model for a 3 Loop phased array.
>
>I have used a similar phasing scheme for the MW 2 Element Phased
>loop array and a Phased Vertical array.
>
>73
>Andrew
>
>
>
>"Hello Guys
>
>Having struggled to model an 3 element endfire Active Vertical array
>using the same Phasing lines from 0.53MHz to 2.12MHz. I find that I
>can achieve a very good elevation plot with very low rear lobes
>(30dB). Even the plot at 2.65MHz only shows 2 small (22dB) rear
>lobes!!! Also this model is very tolerant of several dB amplitude
>difference on the outer elements providing that the centre element
>is the sum of the 2 outer ones.
>
>I have tried to do the same with the 4 Square, but there is always a
>large rear lobe on the elevation plot 1015dB higher than the 3
>element endfire, no matter how I adjust the phase. Am I doing
>something wrong or is there a fundamental problem with the 4 Square?!
>
>Both arrays have 40m Element spacing.
>
>73
>Andrew G8LUG (not active)"
_______________________________________________
Antennaware mailing list
Antennaware@contesting.com
http://lists.contesting.com/mailman/listinfo/antennaware
