Antennaware
[Top] [All Lists]

Re: [Antennaware] Antennaware Digest, Vol 117, Issue 1

To: k8mp@aol.com, antennaware@contesting.com
Subject: Re: [Antennaware] Antennaware Digest, Vol 117, Issue 1
From: N4ZR <n4zr@comcast.net>
Date: Tue, 5 Feb 2019 11:04:43 -0500
List-post: <mailto:antennaware@contesting.com>
Isn't this list intended primarily for antenna modeling topics?  I think you're much more likely to get a responsive answer on Topband or Towertalk.

73, Pete N4ZR
Check out the Reverse Beacon Network
at <http://reversebeacon.net>, now
spotting RTTY activity worldwide.
For spots, please use your favorite
"retail" DX cluster.

On 2/5/2019 10:45 AM, Joe via Antennaware wrote:
Hey Ward, et al,
This is not related to the original topic but you mentioned BOG antennas and I 
have a question.Is installing a BOG near the ground system of an Inverted-L 
dangerous for a receiver? Separation between them would be about 1/8 
wavelength, perhaps less, from the nearest radial.
In my situation, there would be radials and the BOG(s) in the same body of 
water. I have no clue how much RF current and voltage would be in there.
Thanks, Joe, K8MP

-----Original Message-----
From: Ward Silver <hwardsil@gmail.com>
Cc: antennaware <antennaware@contesting.com>
Sent: Tue, Feb 5, 2019 09:57 AM
Subject: Re: [Antennaware] Antennaware Digest, Vol 117, Issue 1


I would suggest that you contact K9AY directly about the impedance mismatch
- k9ay@k9ay.com

 From my experience and in reviewing a lot of literature, unless the loop is
*really* small, preamplifier noise figure is not significant on the lower
HF and MF bands.  I suppose it might be an issue for desktop rotatable
loops or "Beverage on Ground".

73, Ward N0AX

On Tue, Feb 5, 2019 at 5:43 AM Andrew Ikin <andrew.ikin@btopenworld.com>
wrote:

Hello Ward,

I think I need to rephrase my email. What I am trying to say is, a small
terminated antenna e.g. a Flag or a Waller Flag is noise limited by the
termination resistor. This is because the resistor has a 3dB noise figure.
The antenna loss or low radiation resistance doesn't matter so much as this
loss can be made up with an LNA. The issue is made worse because most
practical
designs have the matching transformer z that is the same as the termination
resistor. Now if we use amplifier with high input z of say 30k Ohms; using
chemandy.com Return loss and mismatch loss calculator
the resistor noise is miss-matched to the amp. by approx. 10dB.

Thus the antenna noise floor should be lower. However, I am assuming that
the LNA has negligible noise when terminated with the antenna. This could
be
a design issue to get the noise figure down to less that 0.5dB!!!

The example I gave using a high z amp. with the K9AY suggests that there is
no loss in gain by using increasing the input z.

73

Andrew  G8LUG

-----Original Message-----
From: Ward Silver
Sent: Monday, February 4, 2019 7:50 PM
To: antennaware@contesting.com
Subject: Re: [Antennaware] Antennaware Digest, Vol 117, Issue 1

A flux-coupled transformer with separate windings provides galvanic
isolation between the feed line shield's outer surface and the loop.
Coupling from the loop to the feed line can upset the pattern and couple
noise on the feed line into the antenna.

It is also a good idea to add a choke of several thousand ohms on the feed
line at the antenna to prevent common-mode current on the outside of the
feed line shield from getting into the cable and becoming differential-mode
signals.  Same concern at the receiving end although most receivers are
well-shielded.

73, Ward N0AX

On Mon, Feb 4, 2019 at 11:00 AM <antennaware-request@contesting.com>
wrote:

Send Antennaware mailing list submissions to
         antennaware@contesting.com

To subscribe or unsubscribe via the World Wide Web, visit
         http://lists.contesting.com/mailman/listinfo/antennaware
or, via email, send a message with subject or body 'help' to
         antennaware-request@contesting.com

You can reach the person managing the list at
         antennaware-owner@contesting.com

When replying, please edit your Subject line so it is more specific
than "Re: Contents of Antennaware digest..."


Today's Topics:

     1. Fw: source impedance of resistor terminated antennas (Andrew Ikin)


----------------------------------------------------------------------

Message: 1
Date: Sun, 3 Feb 2019 23:04:32 -0000
From: "Andrew Ikin" <andrew.ikin@btopenworld.com>
To: <antennaware@contesting.com>
Subject: [Antennaware] Fw: source impedance of resistor terminated
         antennas
Message-ID: <2E4939776E6344ECB4242B584629630C@DESKTOPCPQEP29>
Content-Type: text/plain;      charset="UTF-8"



From: Andrew Ikin
Sent: Sunday, February 3, 2019 10:38 PM
To: antennaware@contesting.com
Subject: source impedance of resistor terminated antennas

Is there any reason why most resistor terminated antennas like the K9AY
and the Flag use a matching transformer to the Rx feed line that has the
same impedance as the termination resistance. The reason for the question
is, such antennas have a ideal match to the 3dB noise generated by the
termination resistor and this resistor has no radiation resistance.
Hence,
for antennas like a small size Flag, the performance could be limited by
the resistor noise.

However, if the antenna is connected to a high zin amp., then the
resistor
noise should be reduced by the miss-match and if the amp. noise figure is
very low, then it may be possible improve the antenna performance?

Winding the clock back 20 years I noticed that the K9AY  Rx matching
transformer could be replaced by a high zin  amp. with a voltage gain of
11dB. The overall gain increase compared to using 9:1 z transformer was
20dB. This increase in gain is what would be expected (11dB amp. plus 9dB
by replacing the 9:1 transformer). Thus, the antenna gain compared to one
without the amp. had not been degraded by using high zin amp.. However,
then I didn?t consider the effect of resistor noise, but this wouldn?t be
an issue with the K9AY.

Is there something else I need to consider?

73

Andrew Ikin
G8LUG

------------------------------

Subject: Digest Footer

_______________________________________________
Antennaware mailing list
Antennaware@contesting.com
http://lists.contesting.com/mailman/listinfo/antennaware


------------------------------

End of Antennaware Digest, Vol 117, Issue 1
*******************************************

_______________________________________________
Antennaware mailing list
Antennaware@contesting.com
http://lists.contesting.com/mailman/listinfo/antennaware



_______________________________________________
Antennaware mailing list
Antennaware@contesting.com
http://lists.contesting.com/mailman/listinfo/antennaware
_______________________________________________
Antennaware mailing list
Antennaware@contesting.com
http://lists.contesting.com/mailman/listinfo/antennaware
_______________________________________________
Antennaware mailing list
Antennaware@contesting.com
http://lists.contesting.com/mailman/listinfo/antennaware
<Prev in Thread] Current Thread [Next in Thread>