[Top] [All Lists]

Sealing of Coax Connectors

Subject: Sealing of Coax Connectors
From: RKILE@delphi.com (RKILE@delphi.com)
Date: Wed Jul 6 23:34:42 1994
                    SEALING OF COAX CONNECTORS
    I've noticed some postings on the reflector regarding the use of tape
and Scotchcoat. Some time ago Allan K7CA and myself embarked on building a 2
meter EME array for the late W7HP. Needless to say, don't rely to much on
Scotchcoat if you live in a area of high UV exposure. The stuff rotts.  Two
days of thunderstorms let in the rain after our usual 300 days of sunshine.
The net result was about 50 Type N connectors replaced along with all the
low loss feeders and phasing stubs.
    CRS "STUF" made by DuPont is a good solution to many of the problems.
Take a tube of STUF and squirt some into the ends of the connectors where
they mate. Then screw them together and let it ooze. Personally I like using
properly sized heatshrink tubing along with stuff on the connector bodies
and connectors. Then liberally cover with #33 electrical tape. This STUF as
it is called helps prevent corrosion and improves the dialectric properties
of the connectors.
    Regarding cables ect. I would direct bury the cables using a good grade
of non contaminating cable. A shallow trench with fine gravel in the bottom
should be adequate. Ground the cable to the base of the tower tied to ground
system and sleep at nights during electrical storms.(Helps reduce induced

73, Bob KG7D
via internet"rkile@delphi.com"

>From GOOSE WD8LLD <GOOSTER@delphi.com>  Thu Jul  7 03:36:27 1994
Message-ID: <01HEEHQ4HNNM95OBCA@delphi.com>

Hi all.  Sorry that it took so long to get these posted but it has been
hectic here after FD.
here are the K8MR 1A FD results. (<200w PEP)

  band       cw        ssb
  160         3          0
   80       276        127
   40       441        307
   20       293        190
   15        41          0
   10         0          0
    6        13         79
    2        10         79
  pkt        19
  sat         1
 -----     -----       -----
total       1097       782   --------->  1879

   total pts. 5910 + 800 bonus

ops:   k8m
    that's  K8MR, KU8E, NZ4K, W8KIC, KG8DN, WD8LLD, +one other that i can not 
recall his call.

73................de goose, wd8lld <gooster@delpji.com>

>From stevem@w8hd.org (Steve Maki)  Thu Jul  7 04:16:02 1994
From: stevem@w8hd.org (Steve Maki) (Steve Maki)
Subject: Hot Buttered Toast...
Message-ID: <199407070316.XAA00609@w8hd.w8hd.org>

Contrary to what most people believe, it is possible (unless working on
something like a HyGain balun which apparently was designed to PREVENT
weatherproofing) to weatherproof connectors with lowly electrical tape
alone, even the cheap kind. Here are the "secrets":

1) Use lots of it. Again, use lots of it. Start an inch from the connector,
build up enough layers on the cable at the start of the connector and other
points of transition so that there isn't a sharp change in diameter anyplace. 

2) Use lots of stretch, but go back over the joint with a layer of not very
stretched tape.

3) Cut, don't break the end. If it is done right, the tape will never
unravel, but to be sure, you can put a ty-wrap over the end.

Self fusing siliconized tape (such as Plysafe) works great, but is a little
difficult to remove.

After trying just about every other method, I've always come back to plain
old vinyl tape. I buy 50 rolls at a time and make it a point to use up as
much of it as I possibly can.

Steve Maki K8LX

>From Tom Frenaye <0002349723@mcimail.com>  Thu Jul  7 05:35:00 1994
From: Tom Frenaye <0002349723@mcimail.com> (Tom Frenaye)
Subject: 205BA design?
Message-ID: <82940707043528/0002349723PK4EM@mcimail.com>

I have an older HyGain 205BA that needs to be moved from one tower to 
another.  While I have it down I'd like to optimize the design.  I seem
to remember an article in NCJ (not in index), or something in one of
the antenna modeling demo programs (YO MN etc) that had the details.
Can anyone point me the right way?

Also, with the "mess" of wires coming into the radio room here I'm 
looking for good ideas on how to label them.  I've managed to label my
cables in a way that attracts cats (they eat the labels).  Most recent
plan is some heavy duty tape and permanent marker pens - but wonder if
there are better ideas out there.

Replies direct to:  2349723@mcimail.com

Thanks!  Tom K1KI

PS: Has anyone tried any of the big Inverted Vee arrays described by WA2WVL in
his talk at Dayton?  What's your experience with multi-element inverted Vees on
40 80 or 160? 

>From Robert Penneys <penneys@brahms.udel.edu>  Thu Jul  7 11:54:40 1994
From: Robert Penneys <penneys@brahms.udel.edu> (Robert Penneys)
Subject: Phonetics
Message-ID: <Pine.3.89.9407070641.A27132-0100000@brahms.udel.edu>

or Winnipesaukee Nebuchadnezzar Three Kalamazoo?

Bob Penneys, WN3K  Frankford Radio Club    N.E.R.D.S.
Internet:  penneys@brahms.udel.edu  Mail: 12 E. Mill Stn. Dr., Newark, DE 19711 
Work: Ham Radio Outlet (DE) 800-644-4476, 9:30-5:30 Eastern  Fax: 302-322-8808 

<Prev in Thread] Current Thread [Next in Thread>
  • Sealing of Coax Connectors, RKILE@delphi.com <=