I believe there is a design problem.
There is a tremendous amout of noise coming out of the front panel, all
across the HF and VHF spectrum. Surely there is AC line cord radiation
as well. The control lines and the PWM lines are all run together, not
separated, and the control panel picks up noise from the motor power
lines (high current, high frequency) and re-radiates it.
Appliance manufacturers are exempt from Part 15 certification, no matter
what type of computer or motor they have in there. They do have a small
AC line filter in there, but it doesn't do much.
After I posted my eham article, about a dozen people contacted me about
their washer, or their neighbors. Another OM, who doesn't list an email
addres anywhere, posted another article that said he reduced his problem
with a big AC line filter and secondarily with beads internally. But my
belief is that his antenna was far enough away that the emissions from
the device itself weren't an issue.
In short, I think it is thw Whirlpool Duet and Sears washers are
designed with little thought to RFI/EMC, and that the subcomponents done
in Germany might be OK, but the line filtering and the cable dress and
suppression and shielding internally are inadequate, and serve to
exacerbate the problem.
Leigh/WA5ZNU
On Fri, 2 Jun 2006 1:53 pm, Lee Hill wrote:
> The noise source is either from the PWM motor control or the
> microprocessor.
> The path is out the long AC power cable. Twisting the wires won't help
> the
> unless there was an unlikely huge design oversight with the placement
> of
> return wires. Beads won't help nearly as much as the line to line and
> line
> to chassis capacitors inside the AC line filter. The beads that most
> hams
> have peak Z at 100-200 MHz, and will present maybe 10 to 50 ohms max at
> 20m, and probably much less at 75m.
>
> If the AC power line filter doesn't fix it, it is possible the control
> and
> power wires leaving the microprocessor board are the radiating antenna,
> in
> which case the unit is probably exceeding FCC limits, since the
> radiating
> antenna is so small and noise being detected is so big. And this
> problem is
> non trivial to fix unless you work on EMI problems all the time. Much
> more
> likely the AC power cord is the path/antenna between the source and the
> rig's antenna.
>
> 73
> Lee
> WB1ADR
>
> -----Original Message-----
> From: Leigh L Klotz, Jr. [mailto:Leigh@WA5ZNU.org]
> Sent: Friday, June 02, 2006 4:38 PM
> To: Lee Hill; rfi@contesting.com
> Subject: Re: [RFI] RFI Digest, Vol 42, Issue 1
>
> In mine, the control and power lines are not beaded, and are not
> twisted. The control lines are a random jumble of ribbon cables, all
> tied into a single wiring harness. It may be that the signals are
> differential, but I doubt it.
> Leigh/WA5ZNU
> On Fri, 2 Jun 2006 10:09 am, Lee Hill wrote:
>> They are using PWM motor control to run the high speed motor.
>> The problem is likely to be low frequency noise coming out the AC line
>> cord.
>> I would buy a high performance AC line filter for a few bucks off
>> ebay.
>> It
>> will work tremendously better than even a correctly selected ferrite
>> alone.
>> Mount the filter body directly to the washer, remove some paint so you
>> get
>> direct contact. Use very short (less than 6 inches, this is only 75mto
>> 20m
>> not 2m) wires between the line filter and the AC input of the washer.
>> Then
>> use a different power cord to go into the line filter. Beware this
>> could
>> void your warranty.
>>
>> Keep the wires between the washer and the filter far away from the AC
>> input
>> cable and where it connects to the "line" side of the filter. The
>> "load"
>> side of the filter connects to the washer. Make sure the filter
>> current
>> rating is above the max listed on the washer. Peak current can reduce
>> the
>> performance of the filter.
>>
>> Insulate and cover the thing properly/securely so no kids, animals, or
>> objects cause fire or electrocution.
>>
>> 73
>>
>> Lee
>> WB1ADR
>>
>> -----Original Message-----
>> From: rfi-bounces@contesting.com [mailto:rfi-bounces@contesting.com]
>> On
>> Behalf Of rfi-request@contesting.com
>> Sent: Friday, June 02, 2006 12:00 PM
>> To: rfi@contesting.com
>> Subject: RFI Digest, Vol 42, Issue 1
>>
>> Send RFI mailing list submissions to
>> rfi@contesting.com
>>
>> To subscribe or unsubscribe via the World Wide Web, visit
>> http://lists.contesting.com/mailman/listinfo/rfi
>> or, via email, send a message with subject or body 'help' to
>> rfi-request@contesting.com
>>
>> You can reach the person managing the list at
>> rfi-owner@contesting.com
>>
>> When replying, please edit your Subject line so it is more specific
>> than "Re: Contents of RFI digest..."
>>
>>
>> Today's Topics:
>>
>> 1. Re: Washer RFI/EMI (Paul Christensen)
>>
>>
>> ----------------------------------------------------------------------
>>
>> Message: 1
>> Date: Thu, 1 Jun 2006 20:25:14 -0400
>> From: "Paul Christensen" <w9ac@arrl.net>
>> Subject: Re: [RFI] Washer RFI/EMI
>> To: <rfi@contesting.com>
>> Message-ID: <008301c685db$04d2e560$033ca8c0@Dorm>
>> Content-Type: text/plain; format=flowed; charset="iso-8859-1";
>> reply-type=original
>>
>>> I've had no RFI problems with my LG High Efficiency Washer/Dryer.
>>> It's quieter than my CRT television.
>>
>> I have +40 dB/S9 noise on 75M from a new GE Harmony Washer and can be
>> heard
>> all the way up through 20M. The dryer appears to emit no RFI/EMI.
>>
>> Is there a common cure among the newer generation of washers?
>>
>> Paul, W9AC
>>
>>
>>
>> ------------------------------
>>
>> _______________________________________________
>> RFI mailing list
>> RFI@contesting.com
>> http://lists.contesting.com/mailman/listinfo/rfi
>>
>>
>> End of RFI Digest, Vol 42, Issue 1
>> **********************************
>>
>>
>> _______________________________________________
>> RFI mailing list
>> RFI@contesting.com
>> http://lists.contesting.com/mailman/listinfo/rfi
>
>
> _______________________________________________
> RFI mailing list
> RFI@contesting.com
> http://lists.contesting.com/mailman/listinfo/rfi
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
|