Don,
Thanks for the suggestion. The 847 in the video does two meters
in all modes. A swing of the 2 meter beam yields no noise. I can tune down to
the airport VOR signal on 118 MHz and copy it clearly with no noise.
I have a portable shortwave receiver and a loop antenna that
served me well in tracking other issues, but I am not hearing the signal with
my portable shortwave receiver and loop. I am not hearing it with the
telescopic antenna either. I have a shortwave receiver in my pickup as well. I
do not hear the noise when driving the neighborhood, so I figure it must be
close…
I have an MFJ-852 receiver it seems to go wild when broadside
to either of my neighbor’s houses, but stays pretty quiet near my transformer
box in the back yard.
I will look into building a flag antenna for my portable
shortwave receiver. I think it is a good next step.
My utilities are underground so there aren’t really poles to
check. I have tried the loop near all the boxes I can find with no results yet 😊
73, Thanks and Keep the suggestions coming!
Gary “Joe” kk0sd
From: Don Kirk <wd8dsb@gmail.com>
Sent: Sunday, March 21, 2021 3:21 PM
To: Gary <gary_mayfield@hotmail.com>
Cc: rfi@contesting.com
Subject: Re: [RFI] New Interference at kk0sd
Hi Gary,
I never like to guess what the source of the RFI might be, but here are some
comments and suggestions.
Do you have a 2 meter beam and a 2 meter radio with AM mode capability? If so
you might be able to hear this noise from your house since it appears very
strong on 20 and 15 meters.
I did a quick analysis of the audio in your recording, and it's possibly arcing
(or switching) which is typically happening at 120 Hz (one time each half of
the sine wave) but sometimes only at 60 Hz, and every other half cycle looks
similar to itself (like something is breaking down easier during one half of
the sine wave versus the other half of the sine wave). The arcing is also
intermittent (sometimes no arcing/switching during the time period of
successive 60 Hz sine waves as an example).
Just because you don’t hear it on the AM broadcast band or 160 meters from your
location does not mean it’s not power line RFI. The more I track down power
line noise the more I’m amazed how band specific it can be when not close to
the faulty pole. If you have a cheap portable AM radio you probably will hear
this junk when you get closer to the source. Using a cars AM radio can be hit
or miss depending on the design of the radio, as it appears modern car AM
radios have gotten much better in their noise blanker technology (I can hear
arcing from a faulty power pole at great distances using the AM radio in my 25
year old Saturn, whereas I often can't hear any arcing when right next to a
faulty pole in other vehicles that are more modern than mine). I suspect you
will be able to hear this on 135 MHz AM when you get very close to the source
if you have an HT that tunes down into the aviation band where the radio would
switch to AM mode or if you have a cheap hand held police scanner capable of
135 MHz, etc.
If you have a portable HF receiver I suggest you build a portable flag (see
March issue of QST) and you will likely find the source of that noise (or
narrow in on its location) very quickly since it appears to be very strong.
It’s appears so strong on 20 and 15 meters in your video that you probably will
not even need a preamp with the portable flag. You should be able to hear that
noise from your yard and then walk right toward it using the portable flag. As
you get close to the source you will likely need to reduce RF gain or insert
attenuation. If it’s power line noise you might need to use 135 MHz AM with
directional antenna when you get very close to the pole to isolate the pole
from adjacent poles, and again would need attenuation (this assumes its a pole
and not an in ground feeder, etc).
Just some thoughts from my end.
73,
Don (wd8dsb)
On Sun, Mar 21, 2021 at 2:02 PM Gary
<gary_mayfield@hotmail.com<mailto:gary_mayfield@hotmail.com>> wrote:
My last problem was tracked down to a neon sign in a neighbors garage. I had
several months of blissful relatively low noise operation, but now have a new
RFI issue.
You can see a recording of it here:
https://www.youtube.com/watch?v=GKf4P44FXMo
I have turned all of the breakers in my home off and run the radio from a
battery and the noise remains.
My neighborhood utilities are all underground.
There are no solar installations in my neighborhood, and the noise is there at
night anyway...
The noise is not detectable on the AM broadcast band, but starts around 2 MHz
and runs to at least 6 meters.
It is there 7 days a week 24 hours a day.
It is not detectable from my pickup when I drive the streets of my neighborhood
(checking both AM broadcast and Shortwave).
If any one has heard something like this, I would love to hear what you found.
Thank You for your input and help!
73,
Gary "Joe", kk0sd
_______________________________________________
RFI mailing list
RFI@contesting.com<mailto:RFI@contesting.com>
http://lists.contesting.com/mailman/listinfo/rfi
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
|