TenTec
[Top] [All Lists]

[TenTec] [Fwd: TenTec 10M > 2M transverter]

To: <tentec@contesting.com>
Subject: [TenTec] [Fwd: TenTec 10M > 2M transverter]
From: n4zwq@interpath.com (Jeff Madre)
Date: Mon, 19 May 1997 10:18:30 -0400
This is a multi-part message in MIME format.
--------------3D4FFFA2D404BDE867C41CC7
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit

Paul,

Here's a copy of a message I had sent elsewhere concerning one
of the latest kits.  I wrote this Friday afternoon.  The
circuit board in this kit is beautiful.

73,Jeff

Jeff Madre wrote:
> 
> I received my TenTec 2 meter transverter today and got a very few
> minutes at lunch to look at it .  A few things I noticed are:
> 
> 1.  The case is now deeper from front to back than it is wide.  The
> circuit board is spec'd as being 5.5 X 3.75 inches.  That's 3.75
> from left to right, and 5.5 from front to back.
> 
> 2.  An additional board layout and schematic sheet are provided so you
> can refer to it w/o having to flip pages.
> 
> 3.  The input will accept up to 20W and uses a TO22 format 50 Ohm
                                                 ^^^^ [TO-220]
> load mounted internally.
> 
> 4.  Output power is adjustable from 2 watts to 10 watts using an
> internal adjustment.  Specs indicate 4 watts input ~= 10 watts
> output.  (Can I use this to drive my 2M > 6M 1209?)
> 
> 5.  Specifications claim less than 2 db noise figure with
> approximately 17 db conversion gain.  The transverter uses a
> BF988 (dual-gate MOSFET) in the receiver.
> 
> 6.  The front panel has a power LED and switch as before, but
> also includes a transmit LED.
> 
> 7.  Frequency coverage is 28.0-29.7 = 144.0-145.7.

[TenTec doesn't state that this is the limit.  This is just the example
in the manual.]

> 
> 8.  The price is $139 US for the kit.  I don't know what the
> assembled version costs.
> 
> 9.  My lunches are [not] nearly long enough.
> 
> I hope to start assembling it Sunday and have it on the air next
> week.  I did the 2M > 6M kit build in one marathon session... But
> that was before I found that prolonged exposure to flux smoke
> would kill 50% of my brain _cell_. ;^)
> 
> 73,
> Jeff/N4ZWQ
--------------3D4FFFA2D404BDE867C41CC7
Content-Type: message/rfc822
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

Return-Path: owner-wsvhf@ns1.qsl.net
Received: from ns1.qsl.net (majordom@waller.bwave.com [207.221.20.81]) by 
mail.interpath.net (8.8.5/v1.0-cgb) with ESMTP id PAA23248 for 
<n4zwq@interpath.com>; Fri, 16 May 1997 15:27:05 -0400 (EDT)
Received: (from majordom@localhost) by ns1.qsl.net (8.7.6/8.7.3) id NAA13356 
for wsvhf-outgoing; Fri, 16 May 1997 13:27:11 -0400
X-Authentication-Warning: ns1.qsl.net: majordom set sender to 
owner-wsvhf@qsl.net using -f
Received: from albemarle.cc.nc.us ([198.85.73.14]) by ns1.qsl.net (8.7.6/8.7.3) 
with SMTP id NAA13353 for <wsvhf@qsl.net>; Fri, 16 May 1997 13:27:08 -0400
Received: from jmadre.albemarle.cc.nc.us by albemarle.cc.nc.us 
(SMI-8.6/SMI-SVR4)
        id OAA00533; Fri, 16 May 1997 14:22:44 -0400
Message-ID: <337CA6C2.6978AE68@interpath.com>
To: <tentec@contesting.com>
Date: Fri, 16 May 1997 14:26:10 -0400
From: Jeff Madre <n4zwq@interpath.com>
Organization: http://www.bayside.net/users/carconn.htm
X-Mailer: Mozilla 4.0b4 [en] (Win95; I)
MIME-Version: 1.0
To: QSL Weak Signal Reflector <wsvhf@qsl.net>
Subject: [WSVHF] TenTec 10M > 2M transverter
X-Priority: 3 (Normal)
Content-Type: multipart/mixed; boundary="MimeMultipartBoundary"
Sender: owner-wsvhf@qsl.net
Precedence: bulk
Reply-To: Jeff Madre <n4zwq@interpath.com>

--MimeMultipartBoundary
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit

I received my TenTec 2 meter transverter today and got a very few
minutes at lunch to look at it .  A few things I noticed are:

1.  The case is now deeper from front to back than it is wide.  The
circuit board is spec'd as being 5.5 X 3.75 inches.  That's 3.75
from left to right, and 5.5 from front to back.

2.  An additional board layout and schematic sheet are provided so you
can refer to it w/o having to flip pages.

3.  The input will accept up to 20W and uses a TO22 format 50 Ohm
load mounted internally.  

4.  Output power is adjustable from 2 watts to 10 watts using an
internal adjustment.  Specs indicate 4 watts input ~= 10 watts
output.  (Can I use this to drive my 2M > 6M 1209?)

5.  Specifications claim less than 2 db noise figure with
approximately 17 db conversion gain.  The transverter uses a
BF988 (dual-gate MOSFET) in the receiver.

6.  The front panel has a power LED and switch as before, but
also includes a transmit LED.

7.  Frequency coverage is 28.0-29.7 = 144.0-145.7.

8.  The price is $139 US for the kit.  I don't know what the
assembled version costs.

9.  My lunches are nearly long enough.

I hope to start assembling it Sunday and have it on the air next
week.  I did the 2M > 6M kit build in one marathon session... But
that was before I found that prolonged exposure to flux smoke
would kill 50% of my brain _cell_. ;^)

73,
Jeff/N4ZWQ
--MimeMultipartBoundary--
-----
Submissions: wsvhf@qsl.net
Subscription/removal: wsvhf-request@qsl.net

--------------3D4FFFA2D404BDE867C41CC7--


--
FAQ on WWW:               http://www.contesting.com/tentecfaq.htm
Submissions:              tentec@contesting.com
Administrative requests:  tentec-REQUEST@contesting.com
Problems:                 owner-tentec@contesting.com

<Prev in Thread] Current Thread [Next in Thread>
  • [TenTec] [Fwd: TenTec 10M > 2M transverter], Jeff Madre <=