The reason your TT is not plug capatable with the Alpha is the same reason
Nikon lenses will not fit a Minolta...it is called MARKETING....
and this is not a bad thing, it is simply good business..
but what happened to ham ingenuity??
we have been interfacing rigs from different manufacturers for years....
I hope we havn't reached the point where we need a "HAM RADIO FOR DUMMIES"
it could start with .....if the radios are different colors, they might not
>Aloha from Kauai,
>To Scott and the bunch at Ten Tec, and the guys here
>on the reflector who have already commented to me
>on this topic.
>Problem restated for the guys at Ten Tec:
>Ok, I cannot get the VI+ and the 87A to do their thing. I have
>tried using the 87A in the keying loop a la Ten Tec linears.
>The result, whenever the rig is on, it is transmitting!! I
>connect the Omni TX Out to the 87A relay in; and the
>87A "c" key output back to the Omni TR EN. And it
>is keyed continually ON, no matter what state the
>87A is in; Standby or Operate. There is no response
>of any sort from the 87A, other than it indicates RF
>power passing through, but, if the Omni is on 20 CW,
>and the 87 was last on 40, that's where the 87 stays.
>So the indication from the Omni to the 87 is not taking.
>When the RF output is continuous from the Omni, and I
>press the CW key, the sidetone appears and follows
>the key, but the RF out is constant.
>From what I read about
>the Omni Control Board on pg.. 4-16 in my manual, this
>should work, I think. The manual text says, "the Logic
>board generates a transmit acknowledge voltage at
>connector 63. This drives Q11 which sends the key
>signal over to the Relay on the 87A, as I read it. Then
>the 87A would send the key signal back into the Omni
>TX EN connector, and we should be off and running.
>On the Corsair II, I connected my key signal directly to
>the 87A Relay input; and then keyed back to the
>Corsair II key input from the "c" key output of the 87A;
>that seemed to work fine. Again, tried this with the
>Omni, and it didn't work either.
>I now have had several QSO's: JA, EA, OE, 5V7, SP, DL,
>I, and KC4 down at the South Pole. However, I am using
>the mechanical relay in the Omni to talk to the 87A relay
>input line -- which is driving me nuts with its "clacking".
>That's why I sold the foreign rigs and bought the Omni,
>was to achieve fabulous QSK. But it is not happening.
>There is no way, with my eyes, for me to even begin to
>think of performing the mod Paul, W9AC, has suggested.
>By pass the LCO relay, change the xistor, and key the
>Alpha with the former relay key signal.
>I bought the OmniVI+ especially and specifically for the QSK
>feature, and having had no trouble using QSK of the Corsair II
>with my 87A, presumed this would be duck soup with the
>newer design and better rcvr Omni. Now I am really unhappy!
>I specifically mentioned the 87A in my order to Ten Tec; Scott
>responded with the comment that it was just a matter of connecting
>up RCA jacks, and all would be well. Well I have tried the connections
>for the Ten Tec QSK linears in the manual, and that does not
>seem to work with the 87A, unless there is something obvious
>I have yet to notice.
>However, Jim, W5ODD, has emailed that he has had the same
>experience with his 87A, that is, no QSK ability! And Walt, K8CV,
>sent the following:
> "You probably have it figured out by now, but, when you key the 87
>and it keys the Omni you need to put the jumper plug back in on the
>in and out key thing. From the linear to the Omni is just 2 wire to
>the key ( rca ) jack in. I have never done this but, if you want to
>use the INTERNAL keyer on the Omni then you need the in and out
>thing! With an external keyer just key the amp and let it key the
>rig. Works for me!".
>This sounds as if it is exactly the same set up I used to have QSK with the
>Corsair II and the 87A. Not completely sure I
>understand Walt's input.
>Anyway, in the several years now that both the 87A and the Omni's
>of various generations have been on the market, I have to
>believe someone, and especially someone at Ten Tec
>must know how to set this up in some rather straight forward
>manner so one can have the QSK features of both the Omni
>and the 87A, and also be able to use the Omni with the 87A
>for the occasional SSB QSO. It would seem with the Corsair
>and Walt's solution, you have the 87 available only for CW, unless
>you lock the CW key down when you want to transmit SSB in order
>to tell the amplifier to operate, hi.
>Am sorry to have bumped into this problem within the first
>36 hours of owning the Omni. Sure hope someone on the
>reflector, or at Ten Tec, can come up with the needed
>solution. Not sure I will keep the Omni if this cannot be
>resolved, as that was the principal reason I bought it.
>It is, obviously, in warranty, and for me, this is a warranted
>feature of the Omni, QSK computability with QSK capable
>commercial linears. The only caveat in the Ten Tec manual
>for needing to use the LCO Control Board K1 relay is when
>one is using a non-QSK capable linear (see note on the
>linear of the OmniVI+ manual Fig. 1-10, pg. 1-7.) The
>Alpha 87A is certainly QSK capable!
>73, Jim, KH7M
FAQ on WWW: http://www.contesting.com/tentecfaq.htm
Administrative requests: tentec-REQUEST@contesting.com