|Subject:||Re: [TenTec] QSK/QRQ problem with Orion / ACOM 2000A|
|Date:||Wed, 10 Nov 2004 09:35:55 -0500|
Your friends problem is not funny, but I just have to sit here and chuckle to myself. For some 14 months I have been talking about this problem and having to read the responses of how I must be too dumb to know how to set up a ham station. The Keying Loop and the constant time-shifted CW characters WAS and it STILL IS a firmware problem with the Orion. Everyone will tell your friend that what he is experiencing just is not true, but none of these folks are running CW at speeds over 40 wpm, they just 'forget' to add that fact. But I will tell you that it IS a firmware problem. And at this point, I'm almost convinced that Ten Tec does not know how to solve it.Unfortunately if your friend calls Ten Tec about this, they are NOW telling Orion owners that none of their transceivers are guaranteed to operate QSK above 40 wpm, but they can't explain why if that is the case, their internal keyer is spec'd to operate up to 60 wpm! If you look at the spec's of the Orion, you will not find any mention of QSK, therefore Ten Tec can verbally tell the user what ever they wish, and not have to deal with the problem.
To me, what is really sad, is that Ten Tec built its sterling reputation among CW operators of always producing the very BEST full QSK CW radio available. This is no longer true today, IF you enjoy running CW over about 40 wpm. The sad part, espically coming from the company I truely admired for many, many years, it is now 'let the customer beware'!
In my opinion, if your friend pays some $3300 + USD for a transceiver, plus what ever additional for an amplifier, he SHOULD NOT then have to go out and buy a special keyer to make them work together!
My Omni 6 Plus was sent back to Ten Tec to revert back to logic chip v1.02, simply because it also would not key over 40wpm. I was resoundingly told by the manager of the Ten Tec repair department that reverting back to logic chip v1.02 "had nothing to do with QSK or it's ability to send CW over 40wpm", however after having that change made to my Plus, it now works quite well up to 75 wpm.
My Orion still will not work correctly when using my Titan 3 amplifier in the Keying Loop, however, maricously, the Titan 3 plays flawless when being driven by my Omni 6 Plus or my Icom IC-781.
Tom - W4BQF
----- Original Message ----- From: "NJ0IP" <Rick@dj0ip.de>
To: "Tentec@Contesting. Com" <firstname.lastname@example.org>
Sent: Wednesday, November 10, 2004 4:24 PM
Subject: [TenTec] QSK/QRQ problem with Orion / ACOM 2000A
One of our local hams is having problems mating his Orion 564 to his ACOM 2000A (automatic linear). The problem is only when trying to run full QSK at speeds above 40 wpm. In SSB or when running slower speeds, everything works just fine.
|<Prev in Thread]||Current Thread||[Next in Thread>|
|Previous by Date:||Re: [TenTec] N4PY Orion Control Program Version 1.12 Released, Carl Moreschi|
|Next by Date:||Re: [TenTec] N4PY Orion Control Program Version 1.12 Released, Ken & Linda Burrough|
|Previous by Thread:||Re: [TenTec] QSK/QRQ problem with Orion / ACOM 2000A, Carl Moreschi|
|Next by Thread:||Re: [TenTec] QSK/QRQ problem with Orion / ACOM 2000A, n4lq|
|Indexes:||[Date] [Thread] [Top] [All Lists]|