What diodes do they use?
----- Original Message -----
From: "Tommy" <aldermant@alltel.net>
To: <tentec@contesting.com>
Sent: Thursday, February 03, 2005 14:37
Subject: Re: [TenTec] Re: Paragon Question - Lack of sensitivity
> I'm not sure about the Paragon, but the Omni 6 series radios do use
> cheap JA pin-diodes. (which turned out to be the best one's to use!)
>
> I fell for the idea of replacing all of the Ten Tec installed
> pin-diodes for the 'better' Hewlett-Packard pin diodes, which were
> quite expensive. Course when you change to the HP pin-diodes, you
> have to adjust the current throuh the diodes so they work correct.
> Bottom line was I wasted some nickles and a heck of a lot of time,
> as I found no improvement at all in performance of the Omni 6
> receiver. Actually I would say that the HP pin diodes did not
> preform as well as what Ten Tec had in the radio origanally.
>
> Of course the diodes that switch the band-pass filters (hopefully)
> do not see and are not switched by RF at all. It's all DC switching.
> To obtain the same or better performance when you replace pin-diodes
> you really have to know what current to run through the diodes to
> obtain the best isolation, etc. You are taking some chances when you
> replace Ten Tec component's with something that is 'better'.
>
> I think I have found, over the years of using Ten Tec radio's, the
> best way to 'improve' them is to keep the covers on them at all
> times and keep your paw's out of them...unless of course you adding
> a roofing filter. Not a heck of a lot needs improvement anyway!
>
> Tom - W4BQF
>
> ----- Original Message -----
> From: <c-hawley@uiuc.edu>
> To: <tentec@contesting.com>
> Sent: Thursday, February 03, 2005 9:16 AM
> Subject: Re: [TenTec] Re: Paragon Question - Lack of sensitivity
>
>
> > If these are the diodes that switch in and out the input
> > band pass filters, you are better off with pin diodes which
> > switch much slower than 4148s. The reason is so that strong
> > incoming rf does not switch the diodes that are supposed to
> > be on (or off) for the band you are using. This was a big
> > issue which became popular about 10 years ago. There are
> > some kits available to convert the fast switching diodes to
> > pin diodes. But, don't go and wholesale replace every diode
> > in sight. I think some of these kits were somewhat ill
> > advised. Your receiver may use pin diodes already in many
> > places.
> > Chuck, KE9UW
> >
> > ---- Original message ----
> >>Date: Wed, 2 Feb 2005 15:35:58 GMT
> >>From: "ultrafixedwing@juno.com" <ultrafixedwing@juno.com>
> >>Subject: Re: [TenTec] Re: Paragon Question - Lack of
> > sensitivity
> >>To: tentec@contesting.com
> >>
> >>
> >>Will a 1N914/4148-Type Diode work in the Paragon front end?
> > It's a silicon switching diode. If so, I'll run out and get
> > a handfull.
> >>Thanks,
> >>Paul
> >>KS2S
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|