TenTec
[Top] [All Lists]

Re: [TenTec] Initial comments about ORION II

To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] Initial comments about ORION II
From: "Ron" <ron@morell.us>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sat, 24 Dec 2005 16:54:34 -0800
List-post: <mailto:tentec@contesting.com>
Toby,
No, I do not notice a reduced audio when using the BW encoder from 200Hz to
100Hz and I've tried it several times in UCW mode (I made certain I was
centered on the signal tone).  I do have the 600 Hz roofing filter
installed.  The sub receiver is on VFO A with the Main receiver and using
the same antenna.  The mode is set to UCW for both receivers.  The Sub
receiver is set at a bandwidth of 2200Hz.  I have the hardware noise blanker
turned on, The main receiver set for both headphones and the sub receiver
set for the right headphone.  The sweep display is on.  If you give me all
of your specific settings, I'd be happy to try again.  If I know about
software, each particular setting might be required to replicate the anomaly
you have found.

Thanks for providing me with something to try.  Still not challenged by it
though.  HI
73
Ron  KA7U

-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com]On Behalf Of Toby Pennington
Sent: Saturday, December 24, 2005 11:56 AM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Initial comments about ORION II



Ron,  Do you notice any loss of signal audio when turning the BW encoder
from 200hz  to 100hz in the cw mode?     Not the signal strength but the
audio itself.  I seemed to notice loss of audio the last time I operated the
O2.

----- Original Message -----
From: "Ron" <ron@morell.us>
To: <tentec@contesting.com>
Sent: Friday, December 23, 2005 6:06 PM
Subject: [TenTec] Initial comments about ORION II


> My ORION II arrived yesterday and 15 seconds later it was out of the box
and
> on the air.  I tried it out for several hours yesterday and set it up in
all
> the configurations that caused problems with the ORION.  It did not
develop
> any anomalies that I could detect.  As I currently operate this radio, it
is
> flawless.  I've operated binaural CW with sweep on at the different
levels,
> I've operated CW and PSK, while listening to AM broadcast radio on
receiver
> B with the sweep on, and a variety of other settings that have caused the
> ORION running the latest version 1.3 software to either stop transmitting,
> or stop receiving on Receiver B.
>
> It is a little disappointing, that I'm not yet challenged with software
> anomalies whilst operating the O2.  Maybe someone would enlighten me and
> tell me what parameters are needed to create a fault in this version of
> software?  Perhaps if I read the manual, and consider the instruction
there,
> I'll find a way to create a fault.
>
> I really like this radio and wish all on the reflector and all the folks
at
> Ten Tec a Merry Christmas and a happy New Year!  And thanks for building
> this great radio.
> 73
> Ron  KA7U
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>