TenTec
[Top] [All Lists]

Re: [TenTec] Slaving radios

To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] Slaving radios
From: "Carl Moreschi" <n4py@arrl.net>
Reply-to: Carl Moreschi <n4py@arrl.net>,Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Fri, 20 Apr 2007 10:36:31 -0400
List-post: <mailto:tentec@contesting.com>
You can do it several ways.  If the O7 is near your computer, you can just
connect a serial port from the computer to the O7.  I think the limit on a
serial cable is about 50 feet.  If the O7 is 1200 feet from the shack, you
can run an ethernet cable from the computer to the O7.  My N4PY software
will then control the radio very nicely.  My webpage is at www.n4py.com


Carl Moreschi N4PY
121 Little Bell Drive
Bell Mountain
Hays, NC 28635
----- Original Message ----- 
From: "Larry Menzel" <retire@means.net>
To: "Carl Moreschi" <n4py@arrl.net>; "Discussion of Ten-Tec Equipment"
<tentec@contesting.com>
Sent: Friday, April 20, 2007 10:26 AM
Subject: Re: [TenTec] Slaving radios


> Carl,
>
> Does this require the use of an Internet connection, or directly?
>
> Larry, W0PR
>
>
> ----- Original Message ----- 
> From: "Carl Moreschi" <n4py@arrl.net>
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Sent: Friday, April 20, 2007 8:36 AM
> Subject: Re: [TenTec] Slaving radios
>
>
> > You cannot slave the 2 radios together like you can with Icom radios.
But
> > you can control the Omni VII perfectly from a computer via the serial
port
> > or ethernet port.  I have software for this.
> >
> > Carl Moreschi N4PY
> > 121 Little Bell Drive
> > Bell Mountain
> > Hays, NC 28635
> > ----- Original Message ----- 
> > From: "Larry Menzel" <retire@means.net>
> > To: <TenTec@yahoogroups.com>; "Discussion of Ten-Tec Equipment"
> > <tentec@contesting.com>
> > Sent: Friday, April 20, 2007 9:29 AM
> > Subject: [TenTec] Slaving radios
> >
> >
> >> Good morning all,
> >>
> >> Does anyone know if the new Omni VII with all its features and control
> > stuff can allow two of them to be slaved together...so that anything
done
> > by
> > one will echo on the other via CAT5 cable or some other means?
> >>
> >> Or does it just work via control software and the internet?  A friend
of
> > mine would like to know.  He would trench the cable about 1200 feet if
> > it'll
> > work.
> >>
> >>
> >>
> >> Larry, W0PR
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>