TenTec
[Top] [All Lists]

Re: [TenTec] ORION II and FSK

To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Subject: Re: [TenTec] ORION II and FSK
From: "David W LeJeune, Sr" <lejeuned@centurytel.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sat, 6 Dec 2008 06:47:37 -0600
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
First thing I did was a complete reset (hold down VFOB LCK and power on,
waited for 'Battery Failure', let the rig come up completely, turn it off,
hold down the MAIN RX/TX button and power up, answer yes to both questions)
- but no luck.  I also reloaded 2.37J firmware in hopes that that might fix
it - no luck.  

It's not a real problem - just have to remember to set the RIT to +170 and
the PBT to +170, but would be nice to go back to the way it was.  I fired
off an e-mail to TenTec - perhaps they will have some idea.

Dave WN5V


-----Original Message-----
From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
On Behalf Of pfizenmayer
Sent: Friday, December 05, 2008 10:17 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] ORION II and FSK

Oh , might as well try an "Orion salute" = Master reset - or the whole 
shebang - maybe its little brain got scrambled.


Hank K7HP


battery ----- Original Message ----- 
From: "Duane Calvin" <ac5aa1@gmail.com>
To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Sent: Friday, December 05, 2008 7:18 PM
Subject: Re: [TenTec] ORION II and FSK


>I run FSK through my DigiKeyer a lot, and have not seen this offset.  Not
> sure what to suggest.
>
> 73, Duane
>
> Duane Calvin, AC5AA
> Austin, Texas
> www.ac5aa.com
>
> -----Original Message-----
> From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
> On Behalf Of David W LeJeune, Sr
> Sent: Friday, December 05, 2008 7:06 PM
> To: 'Discussion of Ten-Tec Equipment'
> Subject: [TenTec] ORION II and FSK
>
> This morning I decided to work RTTY and set up the Orion to Mode FSK as
> normal and fired it up.  I use MMTTY and key the FSK line via the EXTFSK
> 1.05 MMTTY plugin and a Rigblaster Pro interface.  Worked fine, but no one
> was answering.  Thought that was strange, so I fired up an aux receiver to
> make sure everything was keying fine.  I Normally use a bandwidth setting 
> of
> about 750 hz.  When I first got the Orion II, in the FSK mode, the 
> bandwidth
> was centered on 2125/2295 as displayed in the MMTTY waterfall display.
> Keying sounded OK on the aux receiver.
>
>
>
> Since I wasn't getting any answers, I changed the bandwidth to 1200 hz and
> fired off a CQ - and sure enough someone answered, but they were 170 hz 
> off
> frequency.  I use the RIT to bring them on freq and had a nice QSO.  Found
> that was normal - everyone else I contacted was 170 hz off, and lo and
> behold, the bandwidth was also off 170 hz - I corrected it in the display
> with the PBT and 170 brought it right back into center with the bandwidth
> narrowed again to 750.
>
>
>
> The manual says that in the FSK mode, the FSK signal is centered in the
> filter bandwidth.  Certainly not the case today, but I know it was
> previously.  What could have changed.  I was able to set things up 
> properly
> with RIT at +170 and PBT at +170, and I saved it as USER 1 profile.  So 
> easy
> enough to reset it.
>
>
>
> Anyone else had this experience?  When I first got the Orion II about 2
> years ago, both the RIT and the PBT were at 0, and the waterfall display 
> was
> perfectly aligned for 2125/2295 tones when I worked RTTY.  Note that this
> was with FSK keying with the MODE switch set to FSK, not AFSK with mode
> switch set to USB.
>
>
>
> Just curious.
>
>
>
> Dave WN5V
>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> 

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>