TenTec
[Top] [All Lists]

Re: [TenTec] TT 705 Mic

To: <wa3fiy@radioadv.com>, "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] TT 705 Mic
From: "DW Holtman" <tubestuff@comcast.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 6 Jan 2009 18:56:29 -0700
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Lee,

Thank you for your help. I have not received the rig yet, hopefully 
tomorrow. The manual should have the pin out for the mic, at least I hope 
so.

Best,
DW Holtman
WB7SSN

----- Original Message ----- 
From: <wa3fiy@radioadv.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Tuesday, January 06, 2009 6:11 PM
Subject: Re: [TenTec] TT 705 Mic


> If you wire the 4 pin plug correctly, the mic will receive it's power 
> directly
> from the Omni VI and the battery will not be needed.  The battery is for
> applications where the radio being used does not provide mic power.
>
> 73,
>
> -Lee-
>
> WA3FIY
>
>
> On 6 Jan 2009 at 17:38, DW Holtman wrote:
>
>> Don,
>>
>> Thank you for the response. This mic has a place for a 9 volt battery. I
>> assume it gets battery power. It has an 8 pin plug, I will have to 
>> install a
>> 4 pin plug. So if you say the pre-amp is needed, I will install the 
>> battery
>> and wire it for the 4 pin plug.
>>
>> Thank you,
>> DW Holtman
>> WB7SSN
>>
>>
>>
>> ----- Original Message ----- 
>> From: "Don Steele" <dsteele@iowatelecom.net>
>> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
>> Sent: Tuesday, January 06, 2009 5:26 PM
>> Subject: Re: [TenTec] TT 705 Mic
>>
>>
>> > DW, The 705 should be wired to plug directly into the Omni 6. It uses 
>> > the
>> > pre amp and should obtaing its power from the rig.
>> >
>> > Don
>> > NT0F
>> >
>> > ----- Original Message ----- 
>> > From: "DW Holtman" <tubestuff@comcast.net>
>> > To: <n2wjw@yahoo.com>; "Discussion of Ten-Tec Equipment"
>> > <tentec@contesting.com>
>> > Sent: Tuesday, January 06, 2009 5:52 PM
>> > Subject: [TenTec] TT 705 Mic
>> >
>> >
>> >> Hello,
>> >>
>> >> I just aquired a Omni VI Plus and from a different source, I have a 
>> >> 705
>> >> mic.
>> >> I'm not familiar with thie mic. It has a circuit board (pre-Amp) built
>> >> in.
>> >> My question, should I use the pre-amp or bypass it and connect the 
>> >> output
>> >> directly to the Omni VI?
>> >>
>> >> Thank you in advance for any advice.
>> >>
>> >> Best,
>> >> DW Holtman
>> >> WB7SSN
>> >>
>> >> _______________________________________________
>> >> TenTec mailing list
>> >> TenTec@contesting.com
>> >> http://lists.contesting.com/mailman/listinfo/tentec
>> >
>> > _______________________________________________
>> > TenTec mailing list
>> > TenTec@contesting.com
>> > http://lists.contesting.com/mailman/listinfo/tentec
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec 

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>