Subject: [TenTec] Noise and ORION II
Content-Type: text/plain; charset="us-ascii"
> I find the NR of the ORION II poor. To my ear the noise of the Orion II
> in SSB is very aggressiv and the NR ist unusable while not doing
> much to reduce the noise. I am setting AGC and RFGain. I must
> reduce the RF-Gain to "60", while the bands are too noisy. This is
> my subjective opinion.
I have an Orion I, and have tried both the 1.x and 2.x firmware. I have found
a similar issue with the 565, which is not too surprising when you consider
that the 565 and 566 are very similar radios, with (according to Ten-Tec) the
same RF hardware and (I believe) the same DSP setup. I have not found the
onboard NR to be at all useful in just about any situation or mode, and I'd say
it has improved signal quality at best around 5% of the time I have needed NR.
My current workaround is a Timewave 59+ outboard DSP processor, which also
solves the low AF output problem into 32 ohm headphones that I had been having.
I am planning on upgrading soon to a Timewave 599zx, which has all the
features for use with the Orion that I find lacking in the 59+ (adjustable NR
aggressiveness, bi-channel NR for stereo phones, filters specifically for more
modern digi-modes). I still wish that I could have decent NR inside my rig
(shoot, my old FT-100D had better NR than my Orion does, and in some ways it
was even better than what I get with the Timewave 59+), and further, I wish
that modern rigs would have something that's been in commercial studio audio
processing gear for decades -- a "side chain". A side chain is a line-level
output between preamp and audio amp (it has other meanings when used with gear
like compressors, but I won't get into that here) combined with a line level
input, essentially letting you insert a
line-level audio processing box before the AF gain knob, almifier, and
speaker(s). This would let me have my binaural receive, put a receiver in each
ear, have a different output on the speaker than in the phones, and have a line
level out on the back panel that had audio processing while simultaneously
having that signal available through phones or speaker. I could just insert an
NR box of my choosing into the signal path without disrupting my output flow
from the rig. With the 59+, I have to set the rig's volume knob appropriately
to feed the 59+, and then I can choose between monaural phones and an external
speaker, and I have to take "line out" from the 59+, which means it is now
affected by the AF level setting on the Orion. The 599zx will take care of the
binaural and different rcvr in each ear issue, but not the other two. And
further, I lose the ability to have my audio monitored, because I have a choice
between processing the monitor audio
through the 59+ or not hearing it at all, neither of which is a suitable
answer for me. Because inp[ut volume is often quite a bit higher than output
volume with the NR turned on, any simple mods I make to solve that issue would
generally result in me getting blasted out of my chair by the high volume level
I'd have with bypassed audio coming to my phones. The 59+ also always has its
high pass/low pass filters engaged when in operation, so it rolls off
everything below 400 hz, which I really do not like either.
Ultimately, if the 599zx turns out to be the real answer for my NR needs, I may
just rewire the Orion such that I send two channels of line level (taken from
the Orion before the rear panel outputs) to the 599zx input, and take the line
level output from the 599zx and inject it back into the signal path just after
where I took the feeds from the Orion in step 1, thus hard-wiring in a side
chain. I don't know how well this will work, considering there will be
variable signal levels depending on signal strength of received signals. But
it does sound like the only real answer to integrating good DSP NR into the
rig, something that Ten-Tec should have given us built in. It is IMHO the one
most glaring flaw of the Orion line (and in a close second place is the
extremely slow speed of the data in/out through the serial port for rig
control, and as a corollary, the fact that there are a number of controls on
the Orion that cannot be accessed by rig control
software, like the band stacking registers and the manual notch filter, for
! Adam Wade -==- AF6ME -==- Ten-Tec Orion & SteppIR BiggIR Mk III !
! "I write down everything I want to remember. That way, instead !
! of spending a lot of time trying to remember what it is I wrote !
! down, I spend z time looking for the paper I wrote it down on." !
! - Beryl Pfizer -=- http://www.allthings550.com !
TenTec mailing list