TenTec
[Top] [All Lists]

Re: [TenTec] additional info re Corsair (" I" ) digital readou

To: tentec@contesting.com
Subject: Re: [TenTec] additional info re Corsair (" I" ) digital readout error
From: "Trevor" <trevor@pshift.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sun, 17 Apr 2011 23:41:25 -0400
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Thanks everyone for pointing out my "duh" about the
VFO jumper-

I'd be embarassed if I weren't so busy being
delighted it's this simple.  

I ever owned a VFO until a couple of years ago when I
picked up a spotless one from Ten-Tec's Used demo
list- and sure enough, last time I had the Corsair
out, I'd hooked up the external VFO- and forgot to
put the jumper back afterwards.  

Thanks again

73
Trevor
KD1YT



------- Original Message -------
>From    : mike bryce[mailto:prosolar@sssnet.com]
Sent    : 4/17/2011 4:18:52 PM
To      : trevor@pshift.com; tentec@contesting.com
Cc      : 
Subject : RE: Re: [TenTec] additional info re Corsair
("I") digital readout error

 this may sound simple, but there's a jumper in the
back that goes 'vfo in---vfo out'

make sure the jumper is in place and seated tightly

without it, the counter won't display correctly
(radio won't work either!)

mike bryce
prosolar@sssnet.com



On Apr 17, 2011, at 1:25 PM, Trevor wrote:

> Some additional info-
> 
> The readout changes from 91.**** to 9.***** when the
> bandswitch is switched to bands where the Corsair is
> usually in upper sideband mode.  It also changes
> slightly when the mode switch is changed from SB-N to
> SB-R.
> 
> Suggestions appreciated- eager to get the rig on the
> air with minimum spinning of wheels
> 
> 73
> Trevor 
> KD1YT
> 
> 
> 
> ------- Original Message -------
>> From    : Trevor[ mailto:kd1yt@pshift.com ]
> Sent    : 4/17/2011 1:12:19 PM
> To      : tentec@contesting.com
> Cc      : 
> Subject : RE: Corsair ("I") digital readout error 
> 
> Hello all--
> 
> I'm the original owner of a Corsair ("1" not II)-
> 
> It's always run flawlessly and I have always given it
> good care/ gentle treatment.
> 
> I've had it stored in boxes for a stretch of years
> now (long story about the rest of life) but ever few
> years, have opened it up and slowly run it up on a
> variac just to keep the capacitors formed.  Last time
> I did that, a bit less than two years ago, all seemed
> well.
> 
> Today I got it out and "brought it up gradually"
> again with the aim of putting it on the air again,
> but the digital readout is reading something like
> 91.000.01-- and does not change regardless of
> switching bands or rotating the VFO.  Turning it off
> and on again does not seem to change anything.
> 
> Suggestions appreciated!
> 
> 73
> Trevor
> KD1YT
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
>  http://lists.contesting.com/mailman/listinfo/tentec 
> 



_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>
  • Re: [TenTec] additional info re Corsair (&quot; I&quot; ) digital readout error, Trevor <=