Thanks Rick. It looks as if Ten Tec never settled on the pin definitions.
They are difference between the OMNI versions. I was hoping that they were
all like the Corsair II, but not so.
----- Original Message -----
From: "Rick - DJ0IP / NJ0IP" <Rick@DJ0IP.de>
To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Sent: Monday, November 07, 2011 4:06 AM
Subject: Re: [TenTec] OMNI D Accessory Jack Pinout
> Wasn't following this thread; been away on business to a Hamfest.
>
> Here is the Pinout:
>
> Pin Function
> 1 T (generated on Control Board 80464)
> 2 + Reg (approx. +8v generated on Control Board 80464)
> 3 +13v
> 4 REM VFO (from OSC-MIXER Board 80455)
> 5 LO (coming from TX Mixer Board 80453)
> 6 C1 (as in Common 1)*
> 7 NO1 (as in Normally Open 1)*
> 8 Ground
> 9 NC1 (as in Normally Closed 1)*
>
> *Mute from OT-TR Board 80281 (The Mute Relay does not control any internal
> functions, but is added for control of external equipment) --> MAN,
> WEREN'T THOSE THE GOOD OLD DAYS! This set of relay contacts was in
> addition
> to the standard External PA control relay! You could even manually
> control
> the timing delay of the drop-out for this relay.
>
> All of this . . . was not so easy to find?
>
> Actually it's all very elementary my dear Mr. Watson:
>
> Begin by locating the Accessory Jack on page 3-6 of the Owner's Manual for
> OMNI-A / OMNI-D.
> You find this jack just under the PTO board 80278 in the middle of the
> fold-out "detailed" block drawing page.
> There you simply trace each line to see where it goes to/from, look up the
> very detailed description of the board that it connects to, and you get
> the
> information above.
>
> Now if you can only locate pin 1 correctly, you're home free!
>
> The Accessory Jack looks like this:
>
> ----------------------
> | 3 6 9 |
> \ |
> / |
> | 2 5 8 |
> \ |
> / |
> | 1 4 7 |
> ----------------------
>
> I *assume* this is the view when looking at the jack on back panel.
> TO BE SURE, Pin 8 is ground so measure what is either pin 2 or 8 and you
> will see which one is grounded.
>
> Hope this helps.
>
> 73
> Rick, DJ0IP
>
>
> -----Original Message-----
> From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
> On Behalf Of Joe
> Sent: Monday, November 07, 2011 3:47 AM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] OMNI D Accessory Jack Pinout
>
> Yes, that is what it says. The only problem is that every online manual I
> have seen does not have that page.
> ----- Original Message -----
> From: "Richards" <jruing@ameritech.net>
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Sent: Sunday, November 06, 2011 8:12 PM
> Subject: Re: [TenTec] OMNI D Accessory Jack Pinout
>
>
>> One of the manuals I have says the pin outs are explained on the MIN
>> BLOCK DIAGRAM.
>>
>> Maybe this helps... depending on if you can find the
>> main block diagram...
>>
>>
>> ========================= James -K8JHR ========================
>>
>>
>> On 11/6/2011 8:46 AM, Joe wrote:
>>> I need to know the pinout of the 9-pin OMNI D accessory jack. I have
>>> looked a several of the online manuals and everyone is missing the block
>>> diagram which has this information. I am guessing that it is the same as
>>> the Corsair II. If someone could give me the info or point me to a
>>> complete manual I would appreciate it.
>>>
>> ------------------------------------------------------------------
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|