TenTec
[Top] [All Lists]

Re: [TenTec] Knob for 227 Tuner

To: wb5jnc@centurytel.net, Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Knob for 227 Tuner
From: k7mks@comcast.net
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sat, 12 Mar 2016 19:23:15 +0000 (UTC)
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Al: Do you happen to have a knob for a 227 antenna tuner. There are 4, all the 
same with a silver colored insert. Physically the same as a bandswitch on a 
Corsair I and 2 and tuner models 238, 229 and many others. 

Thanks joe k7mks 
----- Original Message -----

From: "Al Gulseth" <wb5jnc@centurytel.net> 
To: "Clayton Brantley" <clayton_n4ev@yahoo.com>, "Discussion of Ten-Tec 
Equipment" <tentec@contesting.com> 
Sent: Saturday, March 12, 2016 9:09:00 AM 
Subject: Re: [TenTec] Knob for 229A Tuner 

Simpler than that - just take a small section of a piece of 1/8" or so ty-wrap 
and wedge it into the gap opposite the side where the set screw is. I've 
successfully rescued several of said knobs that way. 

73, Al 

On Sat March 12 2016 10:33:33 am Clayton Brantley via TenTec wrote: 
> Gary: Your friendly TenTec parts supplier in Myrtle Beach has one. It 
> came in error.I was wanting the large cap knob. If your knob is split 
> where it contacts the shaft, thereis a fix. You need a small wire from one 
> of the ties that are on the end of a loaf of breadand tightly wrap and tie 
> it in the recess of the knob. Then fill that recess with epoxy andthe knob 
> is good to go and better than new. The knob maker was trying to save a 
> pennyon the knobs by leaving that material out and therefore making the 
> knob prone to breakage.I have used that fix on several TenTec knobs and 
> have not had a failure. 
> 
> I'll sell you a new knob if that's what you want. Can't remember what they 
> cost but ...I have your address and can get it out. Clayton N4EV 
> 
> 
> 
> From: "Gary H. Harmon, Jr." <gharmon@idworld.net> 
> To: TEN-TEC List <tentec@contesting.com>; 
> ten_tec_radio_net@yahoogroups.com Sent: Saturday, March 12, 2016 11:02 AM 
> Subject: [TenTec] Knob for 229A Tuner 
> 
> Does anyone have any extra Ten Tec knobs? I need one for the bypass 
> switch. 
> 
> 
> 
> 
> Appreciate any help. 
> 
> 
> 
> 73, 
> 
> 
> 
> Gary H. Harmon, Jr. - K5JWK - HAM Radio and ATARI Archaeologist 
> 
> 6003 Archwood 
> 
> San Antonio, TX 78239-1504 
> 
> 210.657.1549 h / 210.884.6926 c/t 
> 
> 210.657.1549 fax with prior notification 
> 
> gharmon@idworld.net 
> 
> 
> 
> "Too many projects - Not enough time!" 
> 
> "Retirement = Every day is a Saturday except Sunday" 
> 
> http://www.grissomroadcoc.org 
> 
> 
> 
> _______________________________________________ 
> TenTec mailing list 
> TenTec@contesting.com 
> http://lists.contesting.com/mailman/listinfo/tentec 
> 
> 
> 
> _______________________________________________ 
> TenTec mailing list 
> TenTec@contesting.com 
> http://lists.contesting.com/mailman/listinfo/tentec 
_______________________________________________ 
TenTec mailing list 
TenTec@contesting.com 
http://lists.contesting.com/mailman/listinfo/tentec 

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>