I didn't try VOX Greg. If this was something I absolutely needed to get
working, I'd do some more experimentation.
We have WinLink running over our Mesh network and I was thinking it would be
nice to have HF capability too.
If I dig back into it, I may try VOX.
Joe, K8MP
-----Original Message-----
From: Greg S via TenTec <tentec@contesting.com>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Cc: Greg S <oldlongbeard@yahoo.com>
Sent: Sun, Mar 4, 2018 8:50 am
Subject: Re: [TenTec] I surrender
Probably not fully compatible with the TT, Joe. Did you try VOX?
73- Greg KC8HXO
Sent from my Linux device
> On Mar 4, 2018, at 08:12, Joe Papworth via TenTec <tentec@contesting.com>
> wrote:
>
> Hmmm...
> I run MMTTY and FLFigi on that same PC over the same connection and they key
> the Omni VI Plus fine.
>
> Those work but WinLink/Winmor does not, so it's gotta be something in the
> program or a setting in it.
>
> Later, Joe, K8MP
>
> Sent from AOL Mobile Mail
>
>
> -----Original Message-----
> From: Carl Moreschi <n4py3@earthlink.net>
> To: k8mp <k8mp@aol.com>
> Cc: tentec <tentec@contesting.com>
> Sent: Sun, Mar 4, 2018 06:54 AM
> Subject: Re: [TenTec] I surrender
>
>
> I don't think the Omni VI implemented that command.
>
> Carl Moreschi N4PY
> 58 Hogwood Rd
> Louisburg, NC 27549
> <a href="http://www.n4py.com"; target="_blank">www.n4py.com</a>
>
>> On 3/4/2018 12:06 AM, <a href="mailto:k8mp@aol.com";>k8mp@aol.com</a> wrote:
>> They're talkin' Carl. The rig accepts the mode and QRG commands from the
>> PC but apparently it doesn't accept the command to xmit.
>>
>>
>> Sent from AOL Mobile Mail
>>
>>
>> -----Original Message-----
>> From: Carl Moreschi <<a
>> href="mailto:n4py3@earthlink.net";>n4py3@earthlink.net</a>>
>> To: Discussion of Ten-Tec Equipment <<a
>> href="mailto:tentec@contesting.com";>tentec@contesting.com</a>>
>> Sent: Sat, Mar 3, 2018 11:12 PM
>> Subject: Re: [TenTec] I surrender
>>
>>
>> There's 3 things that have to match.
>>
>> Baud rate (probably 1200 but might not be )
>> CIV address (should be 04 )
>> Correct comport number.
>>
>> If all those match it will work.
>>
>> Carl Moreschi N4PY
>> 58 Hogwood Rd
>> Louisburg, NC 27549
>> <a href="http://www.n4py.com"; target="_blank">www.n4py.com</a> <<a
>> href="http://www.n4py.com"; target="_blank">http://www.n4py.com</a>>
>>
>>> On 3/3/2018 10:32 PM, Joe Papworth via TenTec wrote:
>>> Gents,
>>>
>>> <div>I threw in the towel on making WinLink and Winmor work with my
>> Omni VI Plus. I have WinLink working over our local Mesh network and I
>> was hoping get it working on HF but no dice.
>>>
>>> Thank you Carl, Rod, Greg, and others who weighed in.
>>>
>>> Joe, K8MP
>>>
>>> Sent from AOL Mobile Mail</div>
>>> _______________________________________________
>>> TenTec mailing list
>>> <a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a> <<a
>>> href="mailto:TenTec@contesting.com?";>mailto:TenTec@contesting.com</a>>
>>> <a href="http://lists.contesting.com/mailman/listinfo/tentec";
>>> target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
>> _______________________________________________
>> TenTec mailing list
>> <a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a> <<a
>> href="mailto:TenTec@contesting.com?";>mailto:TenTec@contesting.com</a>>
>> <a href="http://lists.contesting.com/mailman/listinfo/tentec";
>> target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|