Topband
[Top] [All Lists]

Re: Topband: Subject:RE: New 160M high performance receiving antenna at

To: <topband@contesting.com>
Subject: Re: Topband: Subject:RE: New 160M high performance receiving antenna at W3LPL
From: <donovanf@starpower.net>
Date: Sun, 3 Feb 2013 11:00:31 -0500 (EST)
List-post: <topband@contesting.com">mailto:topband@contesting.com>
Hi Carl,

I and many others have been using Fair-rite 2873000202 binocular cores with 
excellent success for years now.  

http://www.newark.com/fair-rite/2873000202/ferrite-core-cylindrical/dp/02E8908

Using a VNA to measure loss through a pair of back-to-back connected 9:1 
Beverage matching transformers shows much less than 1 dB loss through the pair 
with low VSWR (I don't recall where I stored the detailed measurements I made 
years ago).  I'll repeat the loss and VSWR measurements through pair of 
back-to-back 9:1 transformers, they're trivial to build.

http://www.w8ji.com/Beverages/BEVtrans.jpg

My BSEF receiving array is strictly monoband, the umbrella verticals are tuned 
to resonance at 1840 kHz and the spacings are specific to 160 meters.  Later 
this year I plan to build two fully steerable 8-circle BSEF receiving arrays, 
one for 160 and one for 80 meters.  

http://www.w5zn.org/files/Design%20Construction%20&%20Evaluation%20of%20the%208%20Circle%20Vertical%20Array%20for%20Low%20Band%20Receiving%20Rev%203A%2002-25-2011.pdf

Unlike a passive BSEF receiving array, an array of short verticals with high 
impedance amplifiers at the base of each vertical provides the basis for an 
excellent multi-band receiving array. I don't plan to take that route, I have 
adequate space for monoband BSEF receiving arrays.

http://www.hizantennas.com/4_8_pro_8_element_array.htm

http://www.dxengineering.com/search/department/antennas/section/receive-antennas-and-arrays/part-type/hf-receive-vertical-antenna-array-packages/receive-array-type/eight-circle/product-line/dx-engineering-receive-eight-circle-array-electronics-packages?autoview=SKU

High gain amplifiers at the feedpoints of the verticals can pose a problem in 
the harsh RF environment of a multi-operator multi-transmitter contest station, 
particularly in my case where we have excellent capabilities to simultaneously 
receive within a few kHz of the transmitter.

73
Frank
W3LPL



---- Original message ----
>Date: Sun, 3 Feb 2013 09:22:54 -0500
>From: "ZR" <zr@jeremy.mv.com>  
>Subject: Re: Topband: Subject:RE: New 160M high performance receiving antenna 
>at W3LPL  
>To: <donovanf@starpower.net>
>
>http://www.newark.com/fair-rite/2873000202/ferrite-core-cylindrical/dp/02E8908
>
>
>73 Mix Frank? I thought 31 was the latest choice but for monoband it doesnt 
>matter.
>
>Any plans on doing a 160-40M design?
>
>Carl
>
>
>----- Original Message ----- 
>From: <donovanf@starpower.net>
>To: <topband@contesting.com>
>Cc: "Ron Spencer" <ron.e.spencer@gmail.com>
>Sent: Saturday, February 02, 2013 3:38 PM
>Subject: Topband: Subject:RE: New 160M high performance receiving antenna at 
>W3LPL
>
>
>> Hi Ron,
>>
>> Construction of a phase inversion transformer is covered in detail on page 
>> 23 of the excellent paper published by W5ZN and N4HY:
>>
>> http://www.w5zn.org/files/Design%20Construction%20&%20Evaluation%20of%20the%208%20Circle%20Vertical%20Array%20for%20Low%20Band%20Receiving%20Rev%203A%2002-25-2011.pdf
>>
>> My phase inversion transformer uses the Fairite 2873000202 binocular core 
>> popularized by W8JI for use in Beverage matching and receiving crossfire 
>> transformers.
>>
>> http://www.newark.com/fair-rite/2873000202/ferrite-core-cylindrical/dp/02E8908
>>
>> My transformer windings are made of twisted red and white 26 AWG insulated 
>> telephone wire or you could use Category 5 Ethernet cable or just about 
>> any other small diameter insulated wire.  The twisted pair is passed three 
>> times through both holes in the binocular core (three times returning back 
>> to the starting point of winding).  The red wire is grounded at one end of 
>> the twisted pair and the black wire is grounded at the opposite end of the 
>> twisted pair.  The remaining wires are the input and output of the phase 
>> inversion transformer.   It took me longer to type this explanation than 
>> to fabricate a transformer!
>>
>> I'll be happy to answer any further questions.
>>
>> 73
>> Frank
>> W3LPL
>>
>>
>>
>>
>> ---- Original message ----
>>>Date: Sat, 02 Feb 2013 12:02:24 -0800
>>>From: Ron Spencer <ron.e.spencer@gmail.com>
>>>Subject: BSEF array
>>>To: donovanf@starpower.net
>>>
>>>Frank sounds intriguing. Can you supply details of the phase inverting
>>>transformer?
>>>
>>>Thanks
>>>
>>>Ron
>>>N4XD
>> _________________
>> Topband Reflector
>>
>>
>> -----
>> No virus found in this message.
>> Checked by AVG - www.avg.com
>> Version: 10.0.1430 / Virus Database: 2639/5576 - Release Date: 02/02/13
>> 
>
_________________
Topband Reflector

<Prev in Thread] Current Thread [Next in Thread>