Mini Circuits makes a bias Tee box that has very low insertion loss down
to 500Khz. It is their model*ZX85-12G-S*. and as Tom pointed out there
is a change with current throughput and you can view the chart at
http://research.physics.illinois.edu/bezryadin/labprotocol/ZX85-12Gplus.pdf
I looks like it will do the trick on TopBand but the price of $99.95
each is a bit discouraging.
Herb, KV4FZ
On 1/23/2014 3:18 PM, Tom W8JI wrote:
The Hammond is 400 mA and probably OK, I never used one.
I use something like these 100 uH from Mouser Electronics:
542-73F104AF-RC
or depending on current
542-5250-RC
----- Original Message ----- From: "Pete Smith N4ZR"
<n4zr@contesting.com>
To: "Tom W8JI" <w8ji@w8ji.com>; "Richard (Rick) Karlquist"
<richard@karlquist.com>; "topband reflector" <Topband@contesting.com>
Sent: Thursday, January 23, 2014 1:45 PM
Subject: Re: Topband: Buffaloed by a bias tee
Tom, I appreciate your concern. I have made these changes - I am now
using a shunt choke (homebrew,, measuring 45 uH) and a smaller series
capacitor.. Now all I have to do is to find a source of some
appropriate chokes for the final tee, and my problems may be behind
me. I was just looking at some Hammond chokes, no. 1532h - 100 uH,
rated for maximum DC current of 500 ma., solenoid wound,
self-resonant frequency of 12 MHz. Sound reasonable?
73, Pete N4ZR
Check out the Reverse Beacon Network at
http://reversebeacon.net,
blog at reversebeacon.blogspot.com.
For spots, please go to your favorite
ARC V6 or VE7CC DX cluster node.
On 1/23/2014 12:03 PM, Tom W8JI wrote:
Hi Pete,
You are going to have to trust me on this one.
You really should ***NOT*** be measuring the input of the bias T
with the MFJ 259 B analyzer with the configuration you have.
You can damage the 259 unless you use a smaller series cap and a
shunt choke to protect the 259. The most important point I am trying
to make is ***NEVER*** connect a bias T without a shunt choke,
especially one with a large series coupling cap, to the 259 input
port. The 259 uses 10 volt rated microwave diodes, and the charging
current of the cap can cause that much or more voltage to appear
across the diodes.
Also, if you have a relay outdoors or somewhere, the back EMF from
field collapse can kill the diodes.
I say this all with significant experience on the 259B design. The
MFJ 259 B is not like a regular receiver or transmitter. You are, in
effect, charging a .1uF cap to 12-15 volts through the input port of
the 259.
It's your analyzer, but I can tell you I would not allow anyone here
to do what you are doing with my network analyzers, vector
voltmeters, or my 259B's. I have lost $30K network analyzer diodes
that way, vector voltmeters, and MFJ259/269 diodes that way.
Also, your test does not prove a thing at this point. It does not
prove the inductance is changing. It does not prove the inductance
is not changing either.
The reason it does not prove anything either way is the MFJ is
sensitive to ripple and noise from power supplies that are coupled
to the input port. When you change the supply loading, you also
change the ripple and noise.
So you could be measuring the choke and the choke could be changing,
or you might be measuring the PS ripple or some other change. But
this is secondary to the fact you are connecting a bias T without an
input shunt choke to the 259.
----- Original Message ----- From: "Pete Smith N4ZR"
<n4zr@contesting.com>
To: "Richard (Rick) Karlquist" <richard@karlquist.com>; "topband
reflector" <Topband@contesting.com>
Sent: Thursday, January 23, 2014 11:07 AM
Subject: Re: Topband: Buffaloed by a bias tee
Hi. Well, it does indeed seem to clinch it - when I power the tee
but don't draw any current, the impedance measured by the MFJ does
not change. So now to find some of the right sort of RFC.
73, Pete N4ZR
Check out the Reverse Beacon Network at
http://reversebeacon.net,
blog at reversebeacon.blogspot.com.
For spots, please go to your favorite
ARC V6 or VE7CC DX cluster node.
On 1/22/2014 6:52 PM, Richard (Rick) Karlquist wrote:
On 1/22/2014 12:32 PM, Pete Smith N4ZR wrote:
. However,
as soon as I connect a 12V regulated supply to the bias tee - one
of the
little radio shack variable wallwarts - the measured R drops to 5
ohms
and the X goes up to 19.
Possibly the current through the choke is saturating it.
If you connect the power supply but disconnect the load drawing
current, does the impedance go back to normal? That would
clinch it.
For the choke, be sure that you are NOT using a toroidal choke.
It needs to be a solenoidal type wound on a ferrite rod.
Also, do NOT use "shielded" inductors. Ferrite beads will
also saturate. Most chokes you come across are the wrong
kind. I just bought some chokes today. They only had two
bins of suitable ones, out of several thousand bins of inductors.
45 uH is a little marginal, but doesn't explain your problem.
100 uH would be better.
Rick N6RK
_________________
Topband Reflector Archives - http://www.contesting.com/_topband
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2014.0.4259 / Virus Database: 3681/7027 - Release Date:
01/23/14
_________________
Topband Reflector Archives - http://www.contesting.com/_topband
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2014.0.4259 / Virus Database: 3681/7027 - Release Date:
01/23/14
_________________
Topband Reflector Archives - http://www.contesting.com/_topband
_________________
Topband Reflector Archives - http://www.contesting.com/_topband
|