yes, but what alloy are they? i acquired some very nice aluminum
tubing from a local place up here some years ago, but it has never been
used for anything bigger than a 2m fox hunt beam because they could not
tell me what the alloy was.
James D. Bruce wrote:
> First of all, I'm not affiliated with Lowes or any other store.
> While looking around the Lowes hardware store for household items and just
> window shopping, I found that they have a limited supply of aluminum tubing
> in 8foot sections. The sizes I saw were 3/8" rod, 3/4" tube, 7/8" tube and
> 1" tube. They appear to be the same wall as what is used on my beams &
> verticals and telescope together for a nice fit. They also have the plastic
> end caps. this may be another source for HB antenna projects.
> Jim Bruce
> President/ Owner
> Bruce Communications, Inc.
> (410) 482-2682
> -----Original Message-----
> From: L. B. Cebik <firstname.lastname@example.org>
> To: email@example.com <firstname.lastname@example.org>; email@example.com
> <firstname.lastname@example.org>; QRP-L List <email@example.com>; firstname.lastname@example.org
> Date: Sunday, April 19, 1998 06:49
> Subject: [TowerTalk] junk search--but special junk
> >A while back, I requested help on searching out some junked ground plane
> >rod assemblies. Thanks to Henry Pollock, K4TMC, I now know the specific
> >item I used and could use more of. They are the two piece ground plane
> >rod assemblies that went with the Antenna Specialist/Decibel Products CB
> >ground plane antenna (ASPA2010). Henry sent me a set, but I could use a
> >few more for experiments. They consist of a 5/16 rod and a 3/16, with a
> >coupling that might take a little liquid wrench and gentle force to
> >separate if they have been together very long.
> >AS wants to sell entire antennas, not the pieces. At $169 for the antenna,
> >this is not a practical way to go. Hence, I need an alternate source, if
> >that is possible.
> >a. If anyone knows how to get replacement assemblies inexpensively, the
> >info would be of great help. Insider assitance accepted with gratitutde.
> >b. If anyone has the ground rod parts from a now defunct version of the
> >antenna in question in storage, I would be glad to pay shipping plus some
> >fair small fee for them. They can be separated and them wrapped for UPS
> >To add a sense of mystery to this, they are for my "beam-in-a-boom"
> >design project, which otherwise shows good promise for 10-meter
> >hilltopping from trunk to signal in under 10 minutes.
> >Thanks in advance.
> >LB, W4RNL
> >L. B. Cebik, W4RNL /\ /\ * / / / (Off)(423) 974-7215
> >1434 High Mesa Drive / \/ \/\ ----/\--- (Hm) (423) 938-6335
> >Knoxville, Tennessee /\ \ \ \ / / || / (FAX)(423) 974-3509
> >37938-4443 USA / \ \ \ \ || email@example.com
> > URL: http://funnelweb.utcc.utk.edu/~cebik/radio.html
> >FAQ on WWW: http://www.contesting.com/towertalkfaq.html
> >Submissions: firstname.lastname@example.org
> >Administrative requests: towertalk-REQUEST@contesting.com
> >Problems: email@example.com
> >Search: http://www.contesting.com/km9p/search
> FAQ on WWW: http://www.contesting.com/towertalkfaq.html
> Submissions: firstname.lastname@example.org
> Administrative requests: towertalk-REQUEST@contesting.com
> Problems: email@example.com
> Search: http://www.contesting.com/km9p/search
David Robbins K1TTT (ex KY1H)
firstname.lastname@example.org or email@example.com
FAQ on WWW: http://www.contesting.com/towertalkfaq.html
Administrative requests: towertalk-REQUEST@contesting.com