Towertalk
[Top] [All Lists]

[TowerTalk] FWD: Refurb Your Rohn TB-3 Thrust Bearing

To: <towertalk@contesting.com>
Subject: [TowerTalk] FWD: Refurb Your Rohn TB-3 Thrust Bearing
From: jimi@designet.com (Jim Idelson)
Date: Wed, 9 Dec 1998 17:09:42 -0400
I hope this is now easier to view on your browser . . .

Refurbishing Your Rohn TB-3 Thrust Bearing
Jim Idelson, K1IR

In the last two weeks, I've refurbished two Rohn TB-3 thrust bearings. One was 
running very rough.
The other was "sticking" at several points in its rotation. After refurbishing, 
they both run very smoothly.
This procedure is only intended to help improve the operation of a reasonably 
"healthy" unit. If you find
serious problems, like cracked castings, broken or missing ball bearings, 
extreme wear, or cross-threaded
screws - please do the wise thing and replace it with a brand new thrust 
bearing.

Thanks to Fred, K1VR for providing the thrust bearings to rework, and the 
reminder that I should post
this information for the benefit of all. 

Here's what you'll need:
1.      A clear, well-ventilated, well-lighted workspace
2.      A 16" x 24" or larger tin baking sheet with edges [so you don't lose 
the ball bearings]
3.      A rag for cleaning
4.      Mineral spirits for cleaning
5.      3/16" Allen key [preferably with a 6" handle and "rounded" end for 
insertion at an angle]
6.      Miscellaneous filing tools [i.e. small hand files - round, flat; a 
Dremel tool with fine grinding capability]
7.      Wrenches

Procedure:
1.      Remove all the bolts and nuts that secure the bearing to the tower and 
the mast into the bearing.
2.      OVER THE BAKING TIN, CAREFULLY remove the Allen set screw located on 
the inside wall [where
the mast goes through].
3.      The ball bearings will begin to fall out of the set screw hole. Rotate 
and lightly shake the bearing to
coax the ball bearings out of the hole.
4.      The unit was built with 32 [THIRTY TWO] ball bearings. Make sure you 
have them all! Set them aside.
5.      Separate the top and bottom castings of the bearing.
6.      Clean both castings and all the ball bearings with the rag and the 
mineral spirits or other grease-cutting
cleanser.
        Note:  It is normal for some dirt and metal powder to accumulate. The 
bearing should not contain grease.
This unit is designed to run dry.
7.      Inspect the ball bearing races. Look for unusually worn areas, pitting, 
cracks. Try rolling a ball bearing in
suspect areas to see if it will get "hung".
8.      Using your filing tools, smooth out any rough areas so the ball bearing 
can roll without resistance.
9.      Do this for both castings. Note that your mast will be pushing down on 
the upper casting. This will
cause the bearings to press against the top of the race in the upper casting, 
and against the bottom of the race
in the lower casting. Pay close attention to these areas.
10.     Make sure you look carefully at the area of the race in the upper 
casting near the set screw. I found that
wear in this area was causing one of the thrust bearings to stick.
11.     Insert the set screw - don't cross-thread it! Adjust it to the point 
where a ball bearing can run across it
smoothly. Note, from the insertion side, how far the set screw is screwed in. 
Remove the screw and set it aside.
12.     Reassemble the thrust bearing by holding the castings together and 
inserting the ball bearings back into
the set screw hole one at a time. You'll have to rotate and jiggle the unit to 
find space for the last 5 or 6 ball
bearings. Do this over your baking tin so that WHEN [not IF] you drop a ball 
bearing, it falls in the tin, not in the air
conditioning vent.
13.     Replace the set screw. Insert it until it is at the point you noted in 
Step 11. It should be roughly flush with
the inside wall of the upper casting. Be careful not to cross thread the set 
screw.
14.     Now it's time to give the bearing a spin. It should run much smoother, 
and should not "stick" at all.
15.     If you think the bearing could operate a little smoother, try adjusting 
the set screw in or out a bit. Remember,
the ball bearings must go by the set screw smoothly.
16.     If the unit still sticks . . . return to Step 2. If this is your second 
time through the process and you're still not
satisfied - THROW IT AWAY and go shopping for a new one.

73,

Jim K1IR

-------------------------------------------------------
The Information Resource for Conferencing Professionals
-------------------------------------------------------
James S. Idelson
President
DesigNET International, Inc.
96 Morse Road
Sudbury, Massachusetts USA 01776

tel     978.443.5549
fax     978.443.2034
pager   800.362.0156
email   jimi@designet.com
web     http://www.designet.com

--
FAQ on WWW:               http://www.contesting.com/towertalkfaq.html
Submissions:              towertalk@contesting.com
Administrative requests:  towertalk-REQUEST@contesting.com
Problems:                 owner-towertalk@contesting.com
Search:                   http://www.contesting.com/km9p/search.htm


<Prev in Thread] Current Thread [Next in Thread>
  • [TowerTalk] FWD: Refurb Your Rohn TB-3 Thrust Bearing, Jim Idelson <=