Towertalk
[Top] [All Lists]

[TowerTalk] Fw: BOUNCE towertalk@contesting.com: taboo header: /^cc:\s*

To: <towertalk@contesting.com>
Subject: [TowerTalk] Fw: BOUNCE towertalk@contesting.com: taboo header: /^cc:\s*.+/i Non-member submission from ["Roger Borowski" <k9rb@worldnet.att.net>]
From: mihry@argontech.net (Michael D. Ihry)
Date: Fri, 28 May 1999 16:30:07 -0500

-----Original Message-----
From: owner-towertalk@contesting.com <owner-towertalk@contesting.com>
To: n5kb@contesting.com <n5kb@contesting.com>
To: <towertalk@contesting.com>
Date: Friday, May 28, 1999 4:11 PM
Subject: BOUNCE towertalk@contesting.com: taboo header: /^cc:\s*.+/i
Non-member submission from ["Roger Borowski" <k9rb@worldnet.att.net>]


>>From n5kb  Fri May 28 17:02:34 1999
>Received: from mtiwmhc06.worldnet.att.net (mtiwmhc06.worldnet.att.net
[204.127.131.41])
> by contesting.com (8.9.1a/8.9.1) with ESMTP id RAA11180
> for <towertalk@contesting.com>; Fri, 28 May 1999 17:02:34 -0400 (EDT)
>Received: from main ([208.253.249.156]) by mtiwmhc06.worldnet.att.net
>          (InterMail v03.02.07 118 124) with SMTP
>          id <19990528210232.FVK6854@main>; Fri, 28 May 1999 21:02:32 +0000
>Message-ID: <005e01bea94d$7e8d06a0$a75dfea9@main>
>From: "Roger Borowski" <k9rb@worldnet.att.net>
>To: "J.P. Kleinhaus" <w2xx@cloud9.net>
>Cc: "TowerTalk" <towertalk@contesting.com>
>Subject: Re: [TowerTalk] Mast galvanizing and clearance?
To: <towertalk@contesting.com>
>Date: Fri, 28 May 1999 16:33:32 -0400
>X-Priority: 3
>X-MSMail-Priority: Normal
>X-Mailer: Microsoft Outlook Express 4.72.3110.1
>X-MimeOLE: Produced By Microsoft MimeOLE V4.72.3110.3
>
>It very well can cause problems with clearance, depending how well the
>galvanizer shakes the excess zinc off while it is still molten. More often
>than not, there will be droplets and or even "runs" of zinc on the surface
>to cause problems like you're anticipating. This is the case on nearly
every
>new mast or newly galvanized mast I've seen! To allieviate the clearance
>problem, (and you don't want to find these problems at 120 ft.!), use
>another bearing  (a bearing stop sleeve works too) with the same ID as the
>bearing on the tower while you're still on the ground and check for desired
>clearance. Use an approximately 12" long (by about 1 1/2" wide) flat file
to
>remove the excess zinc in the "problem" areas. There will be no need to
file
>entirely through the zinc coating, just get the boogers off so they're no
>longer causing clearance problems, and the integrity of the galvanizing job
>won't be affected. Checking EVERYTHING first while on the ground makes
tower
>projects go a whole lot smoother. I hope you're project goes well and hope
>I've helped a bit.  73, -=Rog-K9RB=-
>
>-----Original Message-----
>From: J.P. Kleinhaus <w2xx@cloud9.net>
>To: towertalk@contesting.com <towertalk@contesting.com>
To: <towertalk@contesting.com>
>Date: Friday, May 28, 1999 12:08 PM
>Subject: [TowerTalk] Mast galvanizing and clearance?
>
>
>>
>>Greetings:
>>
>>While debating which version of the 4130 mast to buy,
>>I started to wonder if anyone has had trouble with a
>>2" hot-dipped galvanized mast fitting into a 2" thrust
>>bearing?  Did the galvanized finish cause you difficulty
>>at 120 feet in the air?
>>
>>73, J.P. W2XX
>>
>>--
>>FAQ on WWW:               http://www.contesting.com/towertalkfaq.html
>>Submissions:              towertalk@contesting.com
>>Administrative requests:  towertalk-REQUEST@contesting.com
>>Problems:                 owner-towertalk@contesting.com
>>Search:                   http://www.contesting.com/km9p/search.htm
>>
>>
>


--
FAQ on WWW:               http://www.contesting.com/towertalkfaq.html
Submissions:              towertalk@contesting.com
Administrative requests:  towertalk-REQUEST@contesting.com
Problems:                 owner-towertalk@contesting.com
Search:                   http://www.contesting.com/km9p/search.htm


<Prev in Thread] Current Thread [Next in Thread>
  • [TowerTalk] Fw: BOUNCE towertalk@contesting.com: taboo header: /^cc:\s*.+/i Non-member submission from ["Roger Borowski" <k9rb@worldnet.att.net>], Michael D. Ihry <=