Towertalk
[Top] [All Lists]

## [TowerTalk] guy rod angle

 To: [TowerTalk] guy rod angle n0tt1@juno.com (N0TT@ juno.com) Fri, 07 Sep 2001 10:16:05 EDT
 ```Hi gents, My barbershop comments... :) I would think that if there were say, 3 guys running to the same anchor, that one would want to line up the anchor with the "middle" guy wire. If there are two guys then I would think the anchor would line up between the two guys. This is because all the guy wires should be tensioned the same, no one guy wire pulling more than the others during low wind conditions, thus averaging out the load. It would be nearly impossible to predict dynamic wind load on any one guy wire because wind speed is not always the same at all levels of elevation. Thus, there is a logical reason (other than mechanical "neatness") why here are equalizer plates installed at the anchors. BTW, quite a few years ago there was a QST article named "Guys for Guys that have to Guy"...or something to that effect...might be of interest to some of you. 73, Charlie, N0TT On Wed, 05 Sep 2001 22:25:30 -0400 "Michael Rauh" writes: > >Jerry, Stan, Dave, Tom, > >I agree with Jerry and Stan - the angle is probably not critical. >Rohn >presents the angle to 0.1 degree in their guyed tower drawings. This >seems >impossibly precise to me - there is probably way more sag or bow in >the guy >anchor than that. > >I also suspect that Dave is correct when he suggests taking the vector >sum >of the loads on the guys when the tower is at its rated wind load to >find >the guy rod angle. > >In thinking about this problem I realized I don't know how to >calculate the >individual loads on each guy wire. I use a rigid body model for the >tower >that will give the total load on the guys, but won't tell me how the >guys >share the load, at least as far as I can see. To figure out the load >on >each individual guy, I think I will need to consider how the tower >deflects >under load. > >Consider a tower with two sets of guys and an antenna on top. I could >start >by assuming the tower is fixed at the top and the base. I calculate >the >wind load and how the tower will deflect under that load. Draw a >curve, >deflection vs. load. Then assume the lower guy is attached at >mid-point, >draw a curve of elongation vs. load. The load on the second guy is >where >the curves meet. The reminder of the load on the tower, including the > >antenna load, is absorbed by the top guy. > >But wait! The top guy elongates under load too, relieving the load on >the >bottom guy. So I will have to set up a system of simultaneous >equations in >order to get the loads on each guy. I will need equations for the >elongation of the top guy, the bottom guy, the deflection (bowing) and >the >pivoting of the tower. If the tower has a pivot base that is all I >need, >but if the base is cast in concrete I might need an equation to >account for >the force needed to tilt the tower as the guys elongate. > >Does that sound right? Do you know of any references where this kind >of >problem has been worked out? I know Kurt Andress has found guy loads >using >a finite element program. I need to understand the principles >involved >before I resort to a program! > >I think it would be very cool to know how to find the loads on the >individual guy wires in a tower system. > >Best Regards, > >Mike Rauh, NV7X > >Reply to mikerauh@ic.org > > > > >_________________________________________________________________ >Get your FREE download of MSN Explorer at >http://explorer.msn.com/intl.asp > > >List Sponsored by AN Wireless: AN Wireless handles Rohn tower >systems, >Trylon Titan towers, coax, hardline and more. Also check out our self >supporting towers up to 96 feet for under \$1500!! >http://www.anwireless.com > >----- >FAQ on WWW: http://www.contesting.com/FAQ/towertalk >Submissions: towertalk@contesting.com >Administrative requests: towertalk-REQUEST@contesting.com >Problems: owner-towertalk@contesting.com > ________________________________________________________________ GET INTERNET ACCESS FROM JUNO! Juno offers FREE or PREMIUM Internet access for less! Join Juno today! For your FREE software, visit: http://dl.www.juno.com/get/tagj. List Sponsored by AN Wireless: AN Wireless handles Rohn tower systems, Trylon Titan towers, coax, hardline and more. Also check out our self supporting towers up to 96 feet for under \$1500!! http://www.anwireless.com ----- FAQ on WWW: http://www.contesting.com/FAQ/towertalk Submissions: towertalk@contesting.com Administrative requests: towertalk-REQUEST@contesting.com Problems: owner-towertalk@contesting.com ```
 Current Thread [TowerTalk] guy rod angle, David O Hachadorian [TowerTalk] guy rod angle, Mike Rauh [TowerTalk] guy rod angle, Stan or Patricia Griffiths [TowerTalk] guy rod angle, J. Kincade [TowerTalk] guy rod angle, Michael Rauh [TowerTalk] guy rod angle, Stan or Patricia Griffiths [TowerTalk] guy rod angle, N0TT@ juno.com <= [TowerTalk] guy rod angle, Brad Bradfield [TowerTalk] guy rod angle, David Jordan [TowerTalk] guy rod angle, Brad Bradfield [TowerTalk] guy rod angle, Wilf Barby [TowerTalk] guy rod angle, Bob Nielsen [TowerTalk] guy rod angle, Brad Bradfield [TowerTalk] guy rod angle, Stan or Patricia Griffiths [TowerTalk] guy rod angle, J. Kincade [TowerTalk] guy rod angle, N0TT@ juno.com [TowerTalk] guy rod angle, n4kg@juno.com