While we're on the subject...if anyone has a 'spare' bevel gear
from a junker or knows someone who does, I'd appreciate a
referral. I also have need for one of the outer cylindrical motor
housing 'cans'. Both of these are for a 'small' Curtiss/Wright.
Tnx/73, Gerald W5BA email@example.com
----- Original Message -----
From: GALE STEWARD <firstname.lastname@example.org>
To: towertalk reflector <email@example.com>
Sent: Monday, June 03, 2002 7:06 AM
Subject: Re: [Towertalk] Prop-Pitch
> My PP is mounted to a modified Rohn rotator mounting
> plate. I took it to a machine shop and had them cut a
> larger center hole in it. Think it 5 or 6 inch
> diameter. You DO need the bevel gear to make any type
> of coupling to the mast. I used an output shaft and
> clamp assembly from a trashed Hygain RotoBrake 400.
> I need to get up my tower with the digital camera then
> I could post some pix.
> 73, Stew K3ND
> --- dan hearn <firstname.lastname@example.org> wrote:
> > Hi Greg: You are correct, they are mounted to a
> > plate with a hole in it
> > large enough to let the output shaft pass thru it.
> > The unit shown in the
> > ebay add is missing a large bevel gear which mounts
> > to the splined
> > output shaft. Most people weld a bushing to the
> > bevel gear for attaching
> > the tubular mast and the bevel gear takes the
> > vertical load. It is
> > possible to use the splined shaft for output by
> > machining a mating
> > bushing.
> > You do need a direction indicator. If the bevel
> > gear is on the unit,
> > some people make a large gear out of sheet metal the
> > same diameter which
> > will mesh with it to rotate a potentiometer or
> > selsyn. Some of the PP
> > mod articles have dimensions so you can make it with
> > a drill and a file.
> > I have used sprocket and chain drive as well as a
> > small dial cable and
> > pulley arrangement to turn a potentiometer.
> > It is essential that the top of the unit and the
> > indicator you use be
> > protected from weather. I have seen PP motors in
> > flea markets which were
> > not protected and the bevel gear and the ball
> > bearings beneath it are
> > rusted.
> > M2 sells a modified version of their OR 2800
> > control and indicator box
> > for PP motors. You attach a small magnetic pickup to
> > the motor shaft
> > which generates pulses as you rotate and the unit
> > supplies power for the
> > motor.. The price is around $500 I believe.
> > 73, Dan, N5AR
> > Greg Gobleman wrote:
> > >
> > > I was looking at the photos of this prop pitch,
> > not having seen one mounted
> > > I was trying to figure out how they are installed.
> > I assume the flat plate
> > > area is bolted to a stationary plate. Is a
> > notched piece made to adapt to
> > > the mast pipe? I also have read of needing to rig
> > a directional indicator
> > > of some kind. Any info on that? May I assume
> > that the control box and
> > > indicator will probably cost as much as the rotor?
> > >
> > > 73
> > > Greg K9ZM
> > >
> > > _______________________________________________
> > > Towertalk mailing list
> > > Towertalk@contesting.com
> > >
> > _______________________________________________
> > Towertalk mailing list
> > Towertalk@contesting.com
> Do You Yahoo!?
> Yahoo! - Official partner of 2002 FIFA World Cup
> Towertalk mailing list