Towertalk
[Top] [All Lists]

## [Towertalk] 40 meters (Delta Loop)

 To: [Towertalk] 40 meters (Delta Loop) jirka@traveller.cz (Jiri Sanda) Fri, 28 Jun 2002 19:34:07 +0200 (Central Europe Daylight Time)
 ```Hi, one more advice. Each about 0.5 m - 1.5ft of height of the botom wire adds about 50 kHz to the resonance - valid only "close to the ground". i.e. the higher bottom wire is the higher resonace of the whole loop. Optimal height for "low angle" radiation is only up to 2m on 40m. Other good and relatively easy way of transformation is to make a second element - reflector. If both the loops hang down slopping down from the same pole it is directional you get about 3-4 dB and you get some 10-12 dB F/B. If you make the reflector about 3.5% longer you should get something like 50-70 Ohms. 73 ! Jiri OK1RI On Fri, 28 Jun 2002 n4kg@juno.com wrote: > I hope Tim, K3HX, doesn't mind my public answer > to his questions which I expect may be of interest > to several readers. Tom N4KG > > On Fri, 28 Jun 2002 ttt ccccc writes: > > OM, > > > > I'm interested in the delta loop you described for FD. > > > > I'd be grateful if you could answer the following: > > > > 1 How did you feed it....middle of a side or at a corner > > To obtain VERTICAL polarization, a Delta Loop > needs to be fed 1/4 WL down from the APEX (TOP). > Since each side is ~1/3 WL long, this is 0.08 WL > above one of the bottom corners. Feeding at a > bottom corner is mechanically simpler and results > in 'mostly vertical' polarization which is what we do > at our FD site. N4KG > > > > 2 How high was the loop off the ground at the lowest point > > Assuming the Loop circumference is 1WL, each side is > 1/3 WL. IF it is configured as an equilateral triangle, > each corner is 60 degrees and the height is calculated > as 1/3 WL X Sin 60 = 0.333 WL X 0.866 = 0.288 WL > which comes to just over 40 ft for 40M (80 ft for 80M etc). > Subtract the loop height from your support height and you > will know how high the bottom wire is off the ground. > > > > 3 Was it with a side parallel to the ground? > > YES. > > > > 4 What kind of support did you use....conductive or not. > > We used 50 ft high metal lamp posts (between two baseball fields). > > > 5 What were the dimensons and were these for CW or Phone > > The formula for a Delta Loop is 1005 / F (MHz) in feet. > When one side is close to the ground, I find that it needs > to be shortened by about 5%. An antenna analyzer makes > trimming to resonance an easy job. N4KG > > > > 6 What do you suppose the front - to - side figure was like > > As I recall from modeling, the F/S is pretty low, on the order > of 3 dB. Look at the F/S for phased verticals with 1/4 WL > spacing and 0 degrees phasing for comparison. You will see > an oval pattern with very little F/S. N4KG > > > > 7 Any special matching concerns? > > A 1WL Delta Loop looks like 100+ ohms which is easily > transformed to ~50 ohms by any ODD multiple of 75 Ohm > coax. I use 3/4 WL (electrical) of RG59 which comes to 84 ft. > in the CW Band. N4KG > > > > 8 Words of wisdom, counsel or advice....all would be welcome. > > I think we covered all the bases above. Tom N4KG > > > > 73 > > > > Tim K3HX > > > > On Fri, 28 Jun 2002 05:00:50 -0600 n4kg@juno.com writes: > > > Hello Kelly, > > > > > > For Field Day, I used a 50 ft high inverted vee (120 degree apex > > > angle) > > > aimed at W8 and a vertically polarized Delta Loop aimed at W6. > > The Delta Loop gives me 6 to 10 dB improvement to the West Coast after > > > 11 pm local time. The antennas are approximately perpendictular > > > to each other. IMHO, it is NOT worth making a Horizontally > > > Polarized > > > Delta Loop unless you can get the apex much higher (80 to 120 ft) > > > since the effective height is so close to the *bottom* wire. This > > > is not a problem for VERTICALLY polarized loops. > > > > > > For the last two years, I've added a 70 ft reflector to the > > inverted vee > > > and it has been a KILLER, allowing us (K4BFT) to overtake the > > > 20 / 80 CW station for the first time ever. We use the 40M > > inverted vee in 15M where it performs quite well. With the 120 degree > > apex angle, the pattern nulls fill in fairly well, giving us an almost > > > > omni- directional pattern on 15M. We use the 40M Delta Loop on 10M > > > to pick up a few extra contacts on that band as well. > > > > > > Tom N4KG in ALA > > > > > > On Thu, 27 Jun 2002 "Kelly Taylor" > > writes: > > > > Hi all, > > > > > > > > Considering options for SS this fall and I'd like some opinions. > > > > > > > > Options somewhat limited to choice of following: > > > > > > > > Inverted vee, apex 50 feet versus 1wl loop, hung from same > > > yardarm. > > > > > > > > First question: is it even worth doing? > > > > > > > > If so, diamond shape or delta? > > > > > > > > Thanks, > > > > > > > > 73, > > > > kelly > > > > ve4xt > _______________________________________________ > Towertalk mailing list > Towertalk@contesting.com > http://lists.contesting.com/mailman/listinfo/towertalk > ```
 Current Thread [Towertalk] 40 meters (Delta Loop), n4kg@juno.com [Towertalk] 40 meters (Delta Loop), Jiri Sanda <=