Towertalk
[Top] [All Lists]

## [Towertalk] Tower shunt feed for 160 M and modified force12 antennas

 To: [Towertalk] Tower shunt feed for 160 M and modified force12 antennas k2av@contesting.com (Guy Olinger, K2AV) Sat, 6 Jul 2002 23:01:18 -0400
 On something like a C31XR, just outright grounding of the 20m reflector and director will keep the others from breaking down. The arcing occurs because the gap between the boom and element is the "end of the line" for the exciting signal, hence the maximum voltage. If the 20m extreme elements are grounded, then the distance out the booms and the longest elements significantly reduces the voltage at the other gaps. At 1.5 kw on 160m, that's a reduction from a theoretical maximum of over 20 kv to a "mere" 1000v or less anywhere on the boom. Drops it a good deal more on 80m. So probably Tom's idea at ONLY the 20m ref and dir on a C31XR will do just fine. That cuts the number of coils from 11 down to 2. (14 elements in all.) From what I can tell, those two elements effectively control the size of the "top hat" effect anyway. 73, Guy Homework exercise for EZNEC'rs and other model users: Single wire 0,0,0 - 0,0,131 (feet), perfect ground, .5 in conductor, 131 segments, frequency 1.825 MHz. Set source to w1e2, V. Observe feed voltage in Src Dat panel (very high at the top of 1/4 wave). Set source to 87.02% of length from E1 (segment 114) which will be 17 feet from the top (or 1/2 the length of a typical 20m reflector). Which voltage point would you rather insulate? Not absolute figures, of course, but good for order of magnitude. Tom's coil will be effectively invisible at 160 meters, a few ohms reactance in series with the 650-j123 Z at segment 114 in the model at segment. From: "Tom Rauch" To: "Towertalk@Contesting. Com" ; "Henrik Weiss" Sent: Saturday, July 06, 2002 8:23 PM Subject: Re: [Towertalk] Tower shunt feed for 160 M and modified force12 antennas > > The thing is a friend of mine burned the pvc insulator that seperates > > the force12 elements from the boom due to high voltages at the top of > > the tower when running high power. > > > > That is a common problem. > > Ground each of the elements to the boom near the element to > insulation junction. Use a choke coil of about 15-20 turns of #16 or > heavier insulated wire about 1" or 2" in diameter wound in a single > layer solenoid clamped with stainless hose clamps between the element > and the boom. > > That will allow the elements to float for higher bands, and be a > virtual short circuit on 160. It will likely be a bit better for > lighting and other problems, and stop worries about trying to beef up > insulation on the elements. > > It is a much better fix to do this than anything else. > > 73, Tom W8JI > W8JI@contesting.com > > _______________________________________________ > Self Supporting Towers, Wireless Weather Stations, see web site: http://www.mscomputer.com > Call 888-333-9041 to place your order, mention you saw this ad and take an additional 5 percent off > any weather station price. > _______________________________________________ > Towertalk mailing list > Towertalk@contesting.com > http://lists.contesting.com/mailman/listinfo/towertalk >
 Current Thread [Towertalk] Tower shunt feed for 160 M and modified force12 antennas, Henrik Weiss [Towertalk] Tower shunt feed for 160 M and modified force12 antennas, Tom Rauch [Towertalk] Tower shunt feed for 160 M and modified force12 antennas, Guy Olinger, K2AV <=