Towertalk
[Top] [All Lists]

Re: [TowerTalk] Keeping The Mast From Turning (rotating) ??

To: "Mike Rhodes" <weightdn@adelphia.net>, "Tower Talk Reflector" <towertalk@contesting.com>
Subject: Re: [TowerTalk] Keeping The Mast From Turning (rotating) ??
From: "Jim Lux" <jimlux@earthlink.net>
Date: Sat, 30 Aug 2003 15:39:33 -0700
List-post: <mailto:towertalk@contesting.com>
If you don't need accurate positioning to a fraction of a degree, I would
try wrapping some rope around the mast using a stack of turns with some
clove hitches, then tie the rope off to the tower leg.  The rope will
stretch a bit from wind loads, but it has the advantage of having a bit of
"give".
----- Original Message -----
From: "Mike Rhodes" <weightdn@adelphia.net>
To: "Tower Talk Reflector" <towertalk@contesting.com>
Sent: Saturday, August 30, 2003 2:29 PM
Subject: Re: [TowerTalk] Keeping The Mast From Turning (rotating) ??


> Darrell,
>   Hmmm...  Interesting thought...  Not sure the hardware count is reduced
> and the part would be bigger but definitely food for thought. Had not
> thought about trying to use any of the 'in-place' hardware (other than the
> mast and tower itself) as part of the solution. Definitely something to
look
> at. Thanks.
>
> Mike / W8DN
>
> ----- Original Message -----
> From: "Darrell Wright" <kf8kt@comcast.net>
> To: "Mike Rhodes" <weightdn@adelphia.net>
> Sent: Saturday, August 30, 2003 5:11 PM
> Subject: RE: [TowerTalk] Keeping The Mast From Turning (rotating) ??
>
>
> > Hi Mike,
> >
> > I just had a brain storm, yes that is what all the racket was.  Why not
> use
> > a lower mast support for a rotor as a stationary support, it should mate
> up
> > to most any rotor plate.  Let me know if it works.
> >
> > Darrell KF8KT
> >
> > -----Original Message-----
> > From: towertalk-bounces@contesting.com
> > [mailto:towertalk-bounces@contesting.com]On Behalf Of Mike Rhodes
> > Sent: Saturday, August 30, 2003 4:58 PM
> > To: Tower Talk Reflector
> > Subject: [TowerTalk] Keeping The Mast From Turning (rotating) ??
> >
> >
> > Think it has been discussed here before but can't seem to find the
info...
> >
> > Anyhow, just wondering if anyone has come up with a better/easier way to
> > lock the mast when the rotor is not installed. Talking about keeping it
> from
> > freewheeling, not vertical positioning. Already made the mast collars
> > discussed in a previous thread. The piece of steel and a hand full of
> > muffler clamps, nuts, washers, etc., is a real pain, especially when
half
> > the hardware ends up on the ground. Any suggestions?
> >
> > Tnx & 73 de
> > Mike / W8DN
> >
> >
> > _______________________________________________
> >
> > See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless
> > Weather Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with
> any
> > questions and ask for Sherman, W2FLA.
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
> >
> >
> >
>
>
> _______________________________________________
>
> See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless
Weather Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any
questions and ask for Sherman, W2FLA.
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________

See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless Weather 
Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any questions 
and ask for Sherman, W2FLA.

_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>