|To:||<firstname.lastname@example.org>, <email@example.com>, <firstname.lastname@example.org>|
|Subject:||Re: [TowerTalk] Mast Raising Fixture|
|From:||"Mark - AA6DX" <email@example.com>|
|Reply-to:||Mark - AA6DX <firstname.lastname@example.org>|
|Date:||Tue, 17 Aug 2004 09:35:49 -0700|
Before someone hurts themselves --|
How you lift a mast that is inside a tower. You tie a pulley with a long line through it on top of the tower. You then drop the line down the tower center with a correct sized pulley (with an eye on top, naturally). The pulley is placed upside down underneath the mast, and the line goes up on the inside to the top of the tower to be fastened. The loose end of the line is thru the first pulley to the bottom, and is then ready for the ground crew to hoist away, the tower monkey only has to guide the mast. A small line ran thru the mast allows this to happen even from the cat bird's seat. I also have a snatch block at the tower base, so the land crew is pulling OUT, not down. Once in place, the mast can be kept from making an unwanted return trip down the tower with a muffler clamp, the thrust bearing(s), the antenna(s), etc. Now ... another advantage is that you can have the antenna on top of the tower FIRST, and feed the mast through the antenna! How kewl is that? Using it to put up stacks is neat, too. Put first aerial in place, ground crew does its work, then next, etc...... you get the picture! To easily raise the antennas, if the situation allows, I use the old contesters' method ... you connect a short mast to the TOP HALF of the boom to mast clamps, and haul the antenna up that way, so it is more or less parallel to the ground and elements not flopping all over. Drop and reconnect guys, if you have them, on the way. At the top, simply slide over the mast, and tighten the pre-positioned clamps and saddles! The take the top ones loose, get rid of the temporary mast, and do the obvious. In the case of putting the antenna on a mast instead of over it, use extra long temporary u-bolts (allthread works here) for the bottom half of the b-t-m bracket, until top ones are in place, then re-place with the correct ones.
Using this method, once the mast is in its correct place, it can easily be used as the gin pole for raising the yagis, etc.. a nice strong hook clipped on the top works swell ... easier yet, use a pulley / snatch block that has a hook on it to begin with! And ... again .. use a block at the bottom of the tower so the ground crew, winch, whatever is not underneath the worker(s) on the tower, and also that makes it very much easier for them to see what is going on and to communicate.
And that's how it is done EASILY. Never ever had a problem doing it that way. Let the retorts begin! HIHI
73 y'all Mark AA6DX
See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless Weather Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any questions and ask for Sherman, W2FLA.
_______________________________________________ TowerTalk mailing list TowerTalk@contesting.com http://lists.contesting.com/mailman/listinfo/towertalk
|<Prev in Thread]||Current Thread||[Next in Thread>|
|Previous by Date:||[TowerTalk] Yaesu G-1000SDX, Manuel Larsson\"Teknik forumet\"|
|Next by Date:||Re: [TowerTalk] Yaesu G-1000SDX, Chuck Lewis|
|Previous by Thread:||RE: [TowerTalk] Mast Raising Fixture, Pete Smith|
|Next by Thread:||[TowerTalk] Tramming, Jim Idelson|
|Indexes:||[Date] [Thread] [Top] [All Lists]|