Towertalk
[Top] [All Lists]

Re: [TowerTalk] Aluminum tarnish removal

To: "'James C. Hall, MD'" <nwtcc@earthlink.net>, "'David Calder'" <towertalk@n4zkf.com>, <towertalk@contesting.com>
Subject: Re: [TowerTalk] Aluminum tarnish removal
From: "Michael Ryan" <mryan001@tampabay.rr.com>
Date: Sun, 6 Jul 2008 20:35:44 -0400
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
Emory Cloth does the trick....just fold it around the element and rub it up
and down the length. It will look like new.  -Mike

-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of James C. Hall, MD
Sent: Sunday, July 06, 2008 8:22 PM
To: 'David Calder'; towertalk@contesting.com
Subject: Re: [TowerTalk] Aluminum tarnish removal


Great stuff, David. I'm writing all this down !

73, Jamie
WB4YDL

-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of David Calder
Sent: Sunday, July 06, 2008 6:44 PM
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Aluminum tarnish removal


600 Wet/Dry sandpaper and put the element in a drill. Run the sandpaper up
and down the element.
Shines them right up.

73 Dave n4zkf
www.n4zkf.com

 

-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of Larry WA9VRH
Sent: Sunday, July 06, 2008 7:39 PM
To: James C. Hall, MD; 'TowerTalk List'
Subject: Re: [TowerTalk] Aluminum tarnish removal

Hi Jamie,

I have had good luck with S.O.S. steel wool soap pads.  I know people get
freaked out about the steel part but I never found that to be an issue. 
Cleaned up a couple of TA-33's and also a 40' Heights Aluminum towers.  This
was a real mistake but once I started I had to finish as it looked so good I
had no choice!

73 Larry WA9VRH


----- Original Message -----
From: "James C. Hall, MD" <heartdoc@nwtcc.com>
To: "'TowerTalk List'" <towertalk@contesting.com>
Sent: Sunday, July 06, 2008 6:21 PM
Subject: [TowerTalk] Aluminum tarnish removal


> Hi All:
>
>
>
> I noticed this past FD that my F12 C3S had a bit of tarnish that was 
> causing
> some resistance when trying to nest the tubes after the event. I know I
> probably should have been doing this all along, but what is the consensus 
> on
> aluminum oxidation and tarnish removal ? I've tried Scotchbrite pads,
> Brasso, and Maaso metal polish. The Brasso works the best but really takes
> some elbow grease. I worked for a few hours today and got a couple of
> elements looking reasonable but with a few residual tarnish spots. I was
> beat after that !
>
>
>
> There's got to be a better way. I have some Tarn-X, but it says not to use
> it on aluminum.
>
>
>
> Thanks,
>
>
>
> Jamie
>
> WB4YDL
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk 

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk


_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
No virus found in this incoming message.
Checked by AVG - http://www.avg.com 
Version: 8.0.134 / Virus Database: 270.4.4/1532 - Release Date: 7/3/2008
8:32 AM

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

__________ NOD32 3244 (20080705) Information __________

This message was checked by NOD32 antivirus system.
http://www.eset.com


_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>