[Top] [All Lists]

Re: [TowerTalk] Need Help-Triex H 354 Tower (Not LM 354)

To: <>
Subject: Re: [TowerTalk] Need Help-Triex H 354 Tower (Not LM 354)
From: "Mike" <>
Date: Sun, 14 Jun 2009 07:23:00 -0700
List-post: <">>

Very well written.  I have never had a problem getting parts from Tashjian.
It of course depends on if they still manufacture the Tri-ex tower that you
are looking for parts for, if they do, then the pulleys etc. are available.
My Tri-ex LM-470 is 1980 vintage and the parts are still available because
they still manufacture that tower.

When I was at Delta Cable in Stockton they had an board full of pulley
examples tie wrapped to it, a couple looked to be pretty close to the
pulleys for my tower, so Craig may try a wire rope shop.  They also said
that they could repair the old pulleys (press in new bearings) or get a
replacement pulley (at a price).

So there are options out there.  As you elude to Dave, we are lucky that
Tashjian picked up Tri-ex, or we would have one less tower company and a
source of parts.

Mike, K6BR

-----Original Message-----
[] On Behalf Of WA3GIN


Try taking your worn out parts to a local machine shop.  They'll be happy to

reproduce the parts for you.

Our last supplier of TRI-EX towers, cables, and parts is a small operation 
and has to make a decision on each request as to whether there is any 
reasonable profit possible. I suspect most partial tower refurbishment 
projects like pulley replacements are a loss leader for the business. Now if

you were to order up all new cables, pulleys, and bolts, etc., you might 
have gotten a response but you probably wouldn't have wanted to spend the 
money to do a full refurbishment.  That is the delima for a small business 
like Tashjian.

One thing is for sure...bashing Tashjian in a public forum doesn't help him 
or those of us the rely upon his services to maintian our end-of-life 
monuments to mid-century crank-up towers ;-)

TRI-EX CT-100 Owner
----- Original Message ----- 
From: <>
To: <>
Sent: Saturday, June 13, 2009 10:33 PM
Subject: Re: [TowerTalk] Need Help-Triex H 354 Tower (Not LM 354)

> James
> No this is not a free standing support (view attached jpg). Three legs 
> extend out from the first section to the ground.
> Three turn buckles adjust the tension once anchored. My support is at 
> present not extended, nested for the lack of
> replacement pulley's (2 at the very bottom). I'm having better luck at 
> finding hen's teeth than suitable replacement
> pulley's.  Tashjian Towers Corporation is a joke for replacement parts. 
> Rotor is Yaesu 1000, super thunderbird, and Hygain 3
> element 40 meter.
> regrds
> Craig
> kq6i
> -----Original Message-----
> From: James Archer []
> Sent: Saturday, June 13, 2009 4:53 PM
> To:
> Subject: [TowerTalk] Need Help-Triex H 354 Tower (Not LM 354)
> Thanks for reading this.  I have an old Triex H-354 tower that consists of

> three 20 foot steel welded sections that extend
> up to 54 feet via a manual cable crank winch.  This tower was made by 
> Triex Tower in Visalia, California many years ago
> (Serial number 54003).  The tower is different from the LM 354 in that 
> instead of having a "W" pattern on the sides it uses
> flat bar welded to the tubing that lies horizontally when the tower is 
> standing up. The tower probably weighs in the 350 to
> 450 pound range.  There is a single bolt lug at each of the three corners,

> and is obviously designed to be cranked over.
> Can anyone tell me 1, Is The Tower OK for freestanding configuration? 2, 
> What is the acceptable wind loading on this tower?
> Any advice would be appreciated, thanks in advance from James N3ZS.
> ________________________________


> _______________________________________________
> _______________________________________________
> TowerTalk mailing list


TowerTalk mailing list
No virus found in this incoming message.
Checked by AVG - 
Version: 8.5.364 / Virus Database: 270.12.67/2174 - Release Date: 06/13/09


TowerTalk mailing list

<Prev in Thread] Current Thread [Next in Thread>