Towertalk
[Top] [All Lists]

Re: [TowerTalk] Ham IV rotor reassembly

To: towertalk@contesting.com
Subject: Re: [TowerTalk] Ham IV rotor reassembly
From: Barry Gross <n1eu@yahoo.com>
Date: Sat, 30 Oct 2010 06:07:33 -0700 (PDT)
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
I disassembled and checked - bearing retainers were correct.  I posted photo 
series showing the reassembly:  
http://n1eu.com/ham4.jpg

If there are any experts out there, perhaps you could comment on the first 
photo and whether the vertical level of the lower bearing race looks correct.  
The last photo in the series shows the slightly too large gap to bridge - it's 
very close but just can't get all screws threaded.

Unless a light bulb goes off somewhere, I'll send it on to one of the rotor 
experts to sort out.  

Tnx/73,
Barry N1EU

--- On Sat, 10/30/10, Barry Gross <n1eu@yahoo.com> wrote:

> From: Barry Gross <n1eu@yahoo.com>
> Subject: Re: [TowerTalk] Ham IV rotor reassembly
> To: towertalk@contesting.com
> Date: Saturday, October 30, 2010, 6:35 AM
> Thanks for many responses suggesting
> one of the bearing retainers might be upside down.  I
> carefully installed them with the flange away from the
> central rotating race.  But the suggestion does make
> sense and I'll have to bite the bullet and disassemble again
> to double check (how many bearings will fly free this time?
> hi).
> 
> Tnx/73,
> Barry N1EU
> 
> --- On Sat, 10/30/10, Robert <rgshauger@myyellowstone.net>
> wrote:
> 
> > From: Robert <rgshauger@myyellowstone.net>
> > Subject: Re: [TowerTalk] Ham IV rotor reassembly
> > To: "Barry Gross" <n1eu@yahoo.com>
> > Date: Saturday, October 30, 2010, 3:56 AM
> > 
> > Sounds like one the bearing retainers is upside
> down...
> > retainer flange up on the first one and flange down on
> the
> > second
> > 
> > Bob W7KD
> > 
> > 
> > ----- Original Message ----- From: "Barry Gross"
> <n1eu@yahoo.com>
> > To: <towertalk@contesting.com>
> > Sent: Friday, October 29, 2010 3:56 PM
> > Subject: [TowerTalk] Ham IV rotor reassembly
> > 
> > 
> > > I seem to be stuck at the last step of a Ham IV
> > reassembly and would appreciate any helpful advice. 
> > I've lowered the main assembly into the upside down
> upper
> > housing and made sure the potentiometer arm got seated
> along
> > with the 3 housing guides.  I've got both bearing
> > retainers with proper side down, etc.  I've lowered
> the
> > brake housing into place and lined up the 4 bolt holes
> after
> > releasing the brake but there's just a slightly too
> big gap
> > between the housings for the bolts to reach across and
> get
> > threaded.
> > > 
> > > Is it normal to have to wrestle across a gap
> between
> > the upper/lower housings?  Any tips appreciated.
> > > 
> > > Thanks & 73,
> > > Barry N1EU
> > > 
> > > 
> > > 
> > > _______________________________________________
> > > 
> > > 
> > > 
> > > _______________________________________________
> > > TowerTalk mailing list
> > > TowerTalk@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/towertalk
> > 
> > 
> > 
> 
> 
>       
> _______________________________________________
> 
> 
> 
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
> 


      
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>