[Top] [All Lists]

[TowerTalk] Fw: who's "right" (a tuner question)

To: <>
Subject: [TowerTalk] Fw: who's "right" (a tuner question)
From: "Sam Andrews" <>
Date: Tue, 7 Dec 2010 10:27:02 -0600
List-post: <">>
One possibility to explain the readings on the MFJ instrument when it is
looking into the antenna vs. when it is looking into the tuner input . . .

Usually the Q of a tuner that is tuned to a specific frequency is higher,
and the input bandwidth is narrower, when compared to the input Q and
bandwidth of an antenna (or dummy load).  If the signal source of an
instrument such as the MFJ is not as clean (i.e., spurious nearby
off-frequency signal levels are higher) than a typical transmitter,  one
possible effect is that these spurious signals would be reflected when
applied to the hi-Q tuner input (and detected by the MFJ as reflected
signals), while being absorbed by the antenna (not reflected).

This opinion is not based on actual experience with the MFJ, but on my
experience working on UHF transmitters with spurious signal problems.  When
connected directly to a dummy load, those problems didn't show up, but did
show up when connected to the dummy load through a frequency-selective
circuit, such as a resonant cavity or duplexer).  Same principle, I believe.

73, Sam  AE5L

----- Original Message ----- 
From: "jim feldman" <>
To: <>
Sent: Tuesday, December 07, 2010 1:45 AM
Subject: Re: [TowerTalk] who's "right" (a tuner question)

> ok, a little more testing.  I set up on 7.230.  I tuned via the noise peak
> and then used low power to dial in.  Both the TS-940 and the meter on the
> antenna tuner agreed the match was at or near 1:1. Next, I
> then disconnected the feed from the transceiver and substituted the 
> mfj-259.
> I dialed the vfo on it to 7.23 (or as close as I could get it to stay) and
> the swr needle on the analyzer was by the infinity mark.  I then plugged 
> the
> antenna feed line directly into the mfj and got a 2:1 b/w of 7.23 to 7.33
> that dipped to 1.7:1 in the middle.
> observed: MFJ-259 is ok connected directly to antenna, not ok when feeding
> the T match.  I would have to say that local RF sources are not the cause 
> of
> the difference.  I also verified that the swr as measured by the
> ts-940/tuner was the same at  full power as it was at 7 or so watts.  I'm
> not sure why the tuner and the analyzer don't get along.  I am settled on
> the fact that the inline meters are likely correct.
> The MFJ-259 may be ok for some uses, but driving this T match and antenna
> isn't one of them.
> jim
> w6jmf
> On Mon, Dec 6, 2010 at 5:09 PM, jim feldman <> wrote:
>> It took me a little while to understand how a strong BCB station might do
>> this, but I assume it's because the MFJ "sees" the signal as reflected
>> power?  I didn't (and don't) see that if I plug right into the antenna 
>> feed
>> line.  Someone suggested dialing it in via the tuner/transmitter swr 
>> meters
>> and then checking the match via the MFJ289.  I'll try that this evening 
>> and
>> report back the results (little embarrassed I didn't think to try that).
>> I'm not saying that isn't the case but I've been successfully using the
>> analyzer for some months on vhf antenna projects with quite low matches, 
>> and
>> I also periodically test the trapped vertical, and get back pretty good
>> matches on 10 15 and 20.  Even 40 is pretty good.  75 is just very 
>> narrow,
>> but under 2:1
>> Thanks for everyone's help
>> jim w6jmf
> _______________________________________________
> _______________________________________________
> TowerTalk mailing list


TowerTalk mailing list

<Prev in Thread] Current Thread [Next in Thread>