Re: [TowerTalk] Cadweld One Shot Source

["Roger (K8RI) on TT" <K8RI-on-TowerTalk@tm.net>]

On 11/6/2013 2:48 AM, Ray Benny wrote:
> I used an acetylene torch to ignite my one shot plus Cadwell charges. It
> worked fine. It took about 3 - 4 seconds to ignite each one.
>
> Propane and Map-gas were not hot enough.
They should be if you have the fine grained igniter charge on top. It's 
easily ignited while the more coarse welding charge is not.  I had 
several "Old" charges.  The igniter charge had dropped out of the base 
of the container and poure in with the welding charges. Those, I used 
the OxyAcetylene torch with a #1 tip although any of the smaller tips 
will word as long as the flow isn't high enough to blow the charge out 
of the cup.
73

Roger (K8RI)
> Ray,
> N6VR
>
>
> On Tue, Nov 5, 2013 at 3:27 PM, Roger (K8RI) on TT <K8RI-on-TowerTalk@tm.net
> > wrote:
> > On 11/5/2013 4:39 PM, Les Kalmus wrote:
> >
> > > Try this:
> > >
> > > https://www.platt.com/platt-electric-supply/Electrical-
> > > Connectors-Electrical-Termination/Welding-Cable-Connectors/search.aspx?
> > > SectionID=4&GroupID=7971
> > Be sure this contains the temporary form.
> > They have a phone number to make sure you get what you need.
> > 73
> >
> > Roger (K8RI)
> >
> >
> > > Les W2LK
> > >
> > > On 11/5/2013 4:28 PM, Bob Farkaly wrote:
> > >
> > > > Checked them out earlier. Their website features the Cadweld One Shot
> > > > Plus
> > > > that requires the use of a $135.00 controller for ignition. I was hoping
> > > > to
> > > > be able to use the same lighter I use to light my propane torch and skip
> > > > the
> > > > controller.
> > > >
> > > > Bob
> > > >
> > > > -----Original Message-----
> > > > From: ve4xt@mymts.net [mailto:ve4xt@mymts.net]
> > > > Sent: Tuesday, November 05, 2013 3:30 PM
> > > > To: Bob Farkaly
> > > > Cc: towertalk@contesting.com
> > > > Subject: Re: [TowerTalk] Cadweld One Shot Source
> > > >
> > > > therfc.com
> > > >
> > > > Sent from my iPhone
> > > >
> > > >   On Nov 5, 2013, at 14:27, "Bob Farkaly" <bob@farkaly.com> wrote:
> > > > > I've been looking for Cadweld One Shots that accommodate three wires.
> > > > > Bought several 2-wire Cadwelds from Chris Perri, KF7P, but his website
> > > > > does not list the three wire variety. The manufacturer's part number is
> > > > NT1161L.
> > > >
> > > > > Looking for a source for a few units and any pointers would be
> > > > appreciated.
> > > >
> > > > > Thanks,
> > > > >
> > > > >
> > > > >
> > > > > Bob, K9RHY
> > > > >
> > > > > _______________________________________________
> > > > >
> > > > >
> > > > >
> > > > > _______________________________________________
> > > > > TowerTalk mailing list
> > > > > TowerTalk@contesting.com
> > > > > http://lists.contesting.com/mailman/listinfo/towertalk
> > > > _______________________________________________
> > > >
> > > >
> > > >
> > > > _______________________________________________
> > > > TowerTalk mailing list
> > > > TowerTalk@contesting.com
> > > > http://lists.contesting.com/mailman/listinfo/towertalk
> > > _______________________________________________
> > >
> > >
> > >
> > > _______________________________________________
> > > TowerTalk mailing list
> > > TowerTalk@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/towertalk
> > _______________________________________________
> >
> >
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk