Towertalk
[Top] [All Lists]

Re: [TowerTalk] (no subject)

To: "towertalk@contesting.com" <towertalk@contesting.com>
Subject: Re: [TowerTalk] (no subject)
From: Ken Beals <k6mr@outlook.com>
Date: Tue, 29 Jul 2014 17:34:32 +0000
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
Destiny Electronic has a series of MOVs that use 20K as the model number. Try 
here:


http://destiny-electronic.com.my/userfiles/file/product/electronic-component/varistor/Varistor-20K-Series.pdf


Ken K6MR








From: Will Jones
Sent: ‎Tuesday‎, ‎29‎ ‎July‎, ‎2014 ‎09‎:‎52
To: towertalk@contesting.com





Message: 8
Date: Tue, 29 Jul 2014 01:20:24 -0500
From: "Matt" <maflukey@gmail.com>
To: <towertalk@contesting.com>
Subject: [TowerTalk] FW:  MOV's for Polyphaser Rotor Wire Protection
Message-ID: <03d601cfaaf5$2f7db270$8e791750$@gmail.com>
Content-Type: text/plain;    charset="us-ascii"



I need to replace one that has blown. It says, 20K on one of the MOV's but I 
don't know what that means. I guess I would need one at about 50 volts. 
Bill, N4LB





Hi Bill,

Perhaps someone out there knows the specific answer to your question, but
since I did not see a response (yet) perhaps the little info I know may help
you in some way.  Perhaps someone knowledgeable on MOVs can add more into as
well...

I know that the peak clamping voltage ratings of the MOVs in another similar
rotor protection device that I own are rated at ~2.5 x the maximum RMS VAC
rating of the device (or ~ 1.7 x the PEP VAC rating).  I think these will
deviate a little from mfg to mfg based on the service ratings in AC (or DC
for that matter).  Also, I believe that the peak clamping voltage is some
statistical high point for a specific device as there is some mfg tolerance
involved, so a nominal value might be different.

If you are protecting a rotor, I would suggest considering how well the
power supply voltage is regulated and what the worst case maximum no-load
voltage could be.  Once you have that value, you should be able to look in
the mfg literature and select the device with the next highest service
voltage rating.  Be sure to check if the mfg ratings are RMS or PEP and
convert accordingly.  As mentioned above, the clamping voltage will normally
be higher that the service rating by some margin.



I need to replace one that has blown. It says, 20K on one of the MOV's but I 
don't know what that means.



You may want to take a look at the literature and specifications for MOVs
from a mfg (such as Littlefuse company).  The literature does a pretty good
job of guiding one though the process of selecting an appropriate clamping
voltage for a MOV based on the intended service.

Good luck.

Matt
KM5VI

-----Original Message-----
From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of Will
Jones
Sent: Monday, July 28, 2014 7:17 PM
To: towertalk@contesting.com
Subject: [TowerTalk] MOV's for Polyphaser Rotor Wire Protection

Does anyone know what value of MOV is used in the Polyphaser rotor wire
lightening protector model IS-RCT ?
Bill, N4LB
_______________________________________________
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
<Prev in Thread] Current Thread [Next in Thread>
  • Re: [TowerTalk] (no subject), Ken Beals <=