Towertalk
[Top] [All Lists]

Re: [TowerTalk] Shorty Forty Hose Clamp thread

To: jim.thom@telus.net, ve5ra@sasktel.net
Subject: Re: [TowerTalk] Shorty Forty Hose Clamp thread
From: Gene Smar <ersmar@verizon.net>
Date: Thu, 13 Aug 2015 12:35:24 -0500 (CDT)
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
TT:
 
     Didn't a recent Hints and Kinks in QST say to use two hacksaw blades to 
get a wider Kerf/slot for clamping tube ends?  I know I recently read it 
somewhere.  IAC, make sure the teeth face properly for both blades.
 
 
73 de
Gene Smar  AD3F
 



On 08/13/15, Jim Thomson wrote:

## I have never stripped an SS Tridon hose clamp. Never had the inner tube 
rotate either...BUT
I have never used hose clamps on a .375 inch tip to .500 inch tubing 
interface. All mine were
like 1.375 to 1.25 and 1.25 to 1.125 ....etc, etc,and smallest was .5 inch 
tips to .625 inch.
All the tubes were cleaned and then had penetrox applied. Those Tridon SS 
clamp specs say the
smallest they offer is for .375 inch tubing. Even with a .375 tip, the 
clamp is on the .500 portion.
All I ever used was a Xcelite nut driver..cranked as tight as I could by 
hand. I never lubed the
hose clamps either. On the hb yagis, I used a hacksaw to make the single 
slit, so even the slit
was not as wide as the slot you see on say a 204-BA. IE: my slit was the 
width of the blade...and
aprx 1.5 inchs in length.

## what brand and type of hose clamp were you using that would strip ?

Jim VE7RF


-----Original Message----- 
From: Doug Renwick
Sent: Thursday, August 13, 2015 6:40 AM
To: 'Jim Thomson'
Cc: Tower Talk
Subject: RE: [TowerTalk] Shorty Forty Hose Clamp thread

Jim,
How many SS hose clamps have you stripped? I stripped too many because I
could not get the clamp tight enough to prevent the smaller element from
turning inside the larger. I also found that with more penetrox applied, a
tighter hose clamp is required. So my experience differs from yours.

So torque your gear clamp to the max spec and the smaller element still
turns inside the larger. Common sense would tell you to tighten that clamp
further, possibly stripping it, unless you lubricate it.

You have seen my antennas; are there antenna elements falling off
everywhere?

Doug

I wasn't born in Saskatchewan, but I got here as soon as I could.

-----Original Message-----

## If you tq to their MAX tq figures, the smaller tubing inside will not
spin, even if
you slop penetrox on it. Unless the yagi tips have to be adjustable, then
maybe use
SS hose clamps for the tips only. The rest of the yagi should be using 3
x rivets
at each joint.

Jim VE7RF


---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus 

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>