Towertalk
[Top] [All Lists]

Re: [TowerTalk] HyGain Antenna Quality control issues: Let's Put MFJ in

To: towertalk@contesting.com
Subject: Re: [TowerTalk] HyGain Antenna Quality control issues: Let's Put MFJ in Perspective
From: David Gilbert <xdavid@cis-broadband.com>
Date: Mon, 2 Apr 2018 10:21:27 -0700
List-post: <mailto:towertalk@contesting.com>

That's actually a crock.  I spent close to 35 years in a manufacturing environment (semiconductors), nost of it in management, and as anyone who knows anything about manufacturing will tell you, proper manufacturing processes give you both better quality and lower cost.  Generally speaking, tradeoffs between quality and cost occur at the design level, not at the manufacturing level (although Design for Manufacturability is an important concept).  Poor manufacturing quality occurs through ignorance or indifference, period.   What you don't understand is that how the manufacturing floor looks is key to how the product works. Disputing that simply shows ignorance.

MFJ designs their products to meet a particular price point and that's fine.  But there is simply no valid excuse for the quality level of the stuff they build.  I've bought roughly a dozen items from MFJ over the 50+ years I've been a ham and at least ten of them had quality defects.  Not design limitations ... quality defects. Missing parts, loose screws, bad solder joints, defective components, etc.  MFJ has probably the very worst reputation for quality among any manufacturer of amateur radio equipment and that isn't because we enjoy bashing them.  As you say, though, the solution was simply not to buy from them again and that is exactly what I have done.

Dave  AB7E



On 4/1/2018 4:38 AM, Kenneth D. Moak wrote:
Let's Put MFJ in Perspective

It seems like ragging on MFJ has been, and may always be, a popular sport,
but let's put the whole topic in perspective.

Can you buy higher quality and more expensive products? Sure.

Do most well-heeled hams buy these other products? Sure.

But that is NOT MFJ's target market.  Martin Jue is building equipment for
the average ham looking for functional gear at a reasonable price.  Face it,
most Hams are cheap.  We want it as close to free as possible when we're
young and just starting out.  We also buy MFJ when we just don't need
Agilent or Tektronix specification

Full Disclosure:  As a 40+ years Hams, My XYL and I have bought lots of MFJ,
Hy-Gain, and Cushcraft gear from when we had 42 cents in the bank to as
recently as last month.  We also have Flex radios, JK antennas, and two LUSO
towers.  We're not MFJ "fanboys." We're just trying to look at the whole
picture.

While we're at it, let say it up front:  Lots of folks complain about the
need to "Buy American."  Well face it - without Martin Jue of MFJ, many of
the "Big Names" in Ham Radio would have been extinct right now if MFJ didn't
save these companies to keep them in the US.  Obviously the way they
operated in the past couldn't compete in today's market.

MFJ found a way to compete, and enough people think that the occasional
missing screw or wayward hole is not a big deal.  MFJ's No Matter What
Warranty is also better than you get from most other manufacturers - US or
overseas.

When we started out, we wanted gear that we could afford, that worked well
enough to get us on the air, and if we had to "adjust it" that was ok.  We
had plenty of time and not much money.  MFJ supplied that gear.  We used MFJ
gear, and we had fun!

Frankly we don't care what the assembly room looks like as long as in the
long run the product works.  Actually, we think if anyone looked at the
actual defect rates and not just anecdotal internet "facts," we think the
numbers are way better than suspected.

MFJ is not manufacturing computer CPUs.  In fact, we think if you visited
several of the "high-end" custom antenna houses that you would find very
similar conditions.  Try it.

In the end, Martin Jue provides a service for the overall Amateur radio
community.  He fills a critical need and his sales show it.  He survives
when the companies he saved had failed.

The bottom line is that if you don't like MFJ, go someplace else.  Many
others will take your place in line.

Ken & Karen Moak

KM8AM & KM8Q

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk


_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
<Prev in Thread] Current Thread [Next in Thread>