Good Morning:
You might want to scan the attached brief article, which addresses some of your
points in SRF and Bias-T devices.
http://www.ad5x.com/images/Articles/BiasT3amp.pdf
73,
EdMcCann
AG6CX
Sent from my iPhone
> On Apr 3, 2018, at 10:45 AM, N2TK, Tony <tony.kaz@verizon.net> wrote:
>
> Grant,
> How do you measure for self-resonance and how important is it for what I am
> doing?
> N2TK, Tony
>
> -----Original Message-----
> From: Grant Saviers [mailto:grants2@pacbell.net]
> Sent: Tuesday, April 03, 2018 11:59 AM
> To: N2TK, Tony <tony.kaz@verizon.net>; towertalk@contesting.com
> Subject: Re: [TowerTalk] 12V through coax to switch antennas remotely
>
> I have the same interest for a 160/80m relay switchable receive antenna feed
> design on RG6 and came to the following conclusions (probably better ideas
> out there).
>
> The inductor should have its self resonant frequency at or above the maximum
> frequency to be passed on the coax. I selected a Bourns
> 652-RLB0608 180uH with 235ma current rating and corresponding low R and spec
> 4MHz SRF on a ferrite bobbin. I've seen what appear to be 100uH Miller
> solenoid wound chokes in commercial designs but have never measured their
> SRF.
>
> The capacitors should have a SRF well above the max frequency. I chose
> 0.1uF Kemet 1210 SMD size 500v rated chip caps for the LC block and the C
> pass . The 500v rating is for a big lightning/static/crosstalk safety
> factor. (I can show you some leaded 0.1uf HV ceramics with a measured
> SRF below 2MHz, I gotta wonder how one can make them so bad). SMD
> multi-layer chip caps are really superior to any leaded ceramic.
>
> Elsie showed the DC block yields a 2k or so impedance across RG6 on 160m and
> twice that on 80m, so a few percent loss of signal which for a receive
> antenna is negligible.
>
> Everything in stock at Mouser, not yet delivered.
>
> Grant KZ1W
>
>> On 4/3/2018 6:32 AM, N2TK, Tony wrote:
>> Have a question about the values of the choke to keep RF from the
>> relay and the caps for coupling of the signal. In different products I
>> see quite a bit of different values of both components.
>>
>> For the coupling caps I see values from .01-.2uf. It would seem
>> increasing the value of the cap reduces the Xc. And for the choke I
>> see values of 100uh-2.5mh. And it seems increasing the value of the
>> choke also increases Xl.
>>
>>
>>
>> My application is for 160M and 80M only with receive antennas.
>>
>>
>>
>> My question - does it really make a difference over the values listed
> above?
>> Do all the values offer enough Xc or Xl to not cause any problems? Is
>> there really a recommended "good" value for the caps and coils? Even
>> 100uh offers 1K ohms at 1.8MHZ and .1uf is .8 ohms.
>>
>>
>>
>> Still learning.
>>
>> Tnx
>>
>> N2TK, Tony
>>
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|