I have had one up for 30 years. A Ham4 and 402CD using W8JGU sidemount.
Dunno if available anymore.
There is a fairly close up photo of it on my QRZ if you scroll down near
the bottom of page.
Using a graphics program, I made a custom meter face for the controller so
it is clear where you can't go.
If arm should hit the tower with my setup, it's no big deal, it just
stops/stalled, doesn't damage anything
but would not make a habit of it. Suppose it might burn out the motor if
left driving *ON* after it stops.
With a more serious rotator, e.g., prop pitch or 2800, I suppose it could
damage the rotator.
If you have one of those fancy setups where you just punch in a beam
heading or DX prefix, you might
need limit so it doesn't self-destruct......
73, Don N7EF
On Fri, Jun 5, 2020 at 2:39 PM Robert Harmon <k6uj@pacbell.net> wrote:
> Dumb question. When using the swinging gate, how do you make sure when
> the rotator swings it around it won't hit the tower ?
>
>
> Bob
> K6UJ
>
>
>
> > On Jun 5, 2020, at 1:52 PM, Grant Saviers <grants2@pacbell.net> wrote:
> >
> > I have a Rohn 65 design in CAD, never built it, went with rings
> instead. Should have done the arms. All 1/4" HRS steel plate, standard
> angles and channel, plus 2" NPT pipe, although other tube/pipe choices are
> easy. Different leg diameters depend on the u-bolt size (minor hole
> location change needed). Designed for hot dip galvanizing. I designed for
> two antennas for up to 20' of pipe between top bearing and rotator. Or one
> antenna on a short pivot "mast". Uses a standard mount rotator at the
> bottom (my plan was Orion 2800) and a UHMW bearing at the top. Make the
> plates on a laser or waterjet cutter. Weld it up and HDG.
> >
> > Reply off list and I well send 3D pdf's to review. Enough interest and
> some weld shop might make them. Everything should UPS except the pipe, buy
> it locally. Adding tabs and slots to the top and bottom supports for self
> fixturing of the welding would be nice.
> >
> > Grant KZ1W
> >
> > On 6/5/2020 11:46, Jon Zaimes via TowerTalk wrote:
> >> Try here: http://www.w9iix.com/ii00012.htm
> >> Jon P. Zaimes, AA1K
> >> Tower climber for hire
> >> Website: aa1k.us
> >> Cell: 302-632-2353
> >> Email: jz73@verizon.net
> >> Hug your favorite tower every day, and always stay connected to it
> >> On Friday, June 5, 2020 mike stokes <mike9v@gmail.com> wrote:
> >> I am looking for one as well. Please reply to the list.
> >> 73
> >> Mike
> >> KK9V
> >> On Fri, Jun 5, 2020 at 2:20 PM Ignacy Misztal <no9e@arrl.net> wrote:
> >>> Does anybody make swinging gate mounts? I need one for 45G.
> >>> Ignacy, NO9E
> >>> _______________________________________________
> >>>
> >>>
> >>>
> >>> _______________________________________________
> >>> TowerTalk mailing list
> >>> TowerTalk@contesting.com
> >>> http://lists.contesting.com/mailman/listinfo/towertalk
> >>>
> > _______________________________________________
> >
> >
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|