What operating system are you using? I know you can't use USB ports under
WinNT and at least one other Windows operating system...
-----Original Message-----
From: writelog-admin@contesting.com
[mailto:writelog-admin@contesting.com]On Behalf Of Steve Russell
Sent: 2002 October 11 Fri 23:51
To: Jerry Flanders; writelog@contesting.com
Subject: Re: [WriteLog] CW Keyer - PC generates
Hi Jerry,
No, I have a CT-17 with its own power supply. No, I am trying to use COM1
for keying, COM3 for rig control, so the DTR line on the rig interface
'should' be behaving the same with or without cw keying? Note that I can
use either rig control or keying with writelog, but not both. With dxbase
both work at the same time.
Do you use 'pc-generates' keying?
-Steve
----- Original Message -----
From: "Jerry Flanders" <jeflanders@comcast.net>
To: <writelog@contesting.com>
Sent: Friday, October 11, 2002 11:08 PM
Subject: Re: [WriteLog] CW Keyer - PC generates
> Some of the interface circuits get their power from the signal lines in
the
> com port. Got one of these? You are using the same port for rig control
and
> CW key, right? Does your interface perhaps get power from the DTR line
(only) ?
>
> Jerry W4UK
>
>
> At 21:38 10/11/02 -0400, Steve Russell wrote:
> >Hi Randy,
> >
> >Yes, DXBase sends cw fine. COM1 is interrupt 4, COM3 is USB using
interrupt
> >9.
> >
> >-Steve, AA3ZV
> >
> >----- Original Message -----
> >From: "Randy Thompson, K5ZD" <k5zd@charter.net>
> >To: "Steve Russell" <steve@slrs.com>; <writelog@contesting.com>
> >Sent: Friday, October 11, 2002 6:58 PM
> >Subject: RE: [WriteLog] CW Keyer - PC generates
> >
> >
> > > But is DXBase sending CW?
> > >
> > > Make sure that COM1 and COM3 are not sharing interrupts.
> > >
> > > Randy, K5ZD
> > >
> > > > -----Original Message-----
> > > > From: writelog-admin@contesting.com
> > > > [mailto:writelog-admin@contesting.com]On Behalf Of Steve Russell
> > > > Sent: Friday, October 11, 2002 21:44 PM
> > > > To: writelog@contesting.com
> > > > Subject: [WriteLog] CW Keyer - PC generates
> > > >
> > > >
> > > > As soon as I select 'PC generates' for my CW generation, the
> > > > interface to my rig dies.
> > > >
> > > > I'm using COM3 as rig interface, COM1 as CW (DTR) interface. Rig
> > > > is IC-746pro (using 756pro selection).
> > > >
> > > > DXBase survives this setup, so I don't think it is a com port
problem.
> > > >
> > > > Any ideas?
> > > >
> > > > Thanks!
> > > >
> > > > -Steve
> > > >
> > > >
> > > > --- StripMime Report -- processed MIME parts ---
> > > > multipart/alternative
> > > > text/plain (text body -- kept)
> > > > text/html
> > > > ---
> > > > _______________________________________________
> > > > WriteLog mailing list
> > > > WriteLog@contesting.com
> > > > http://lists.contesting.com/mailman/listinfo/writelog
> > >
> >
> >_______________________________________________
> >WriteLog mailing list
> >WriteLog@contesting.com
> >http://lists.contesting.com/mailman/listinfo/writelog
>
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
|