WriteLog
[Top] [All Lists]

[WriteLog] FSK with Rascal inteface and 756Pro

To: <writelog@contesting.com>
Subject: [WriteLog] FSK with Rascal inteface and 756Pro
From: wa5chx@arrl.net (Roland Guidry - WA5CHX)
Date: Sat Apr 5 10:48:22 2003
Thanks to all those that replied to my message, especially Bill Metzger who
can up with the correct suggestions for setup.

This is what I did:

Switch PC control to the USB to COM2
Selected COM1 for rig control in Writelog
Selected Setup and made PTT COMM = NO in Writelog
Saved Configuration "important"
Selected COM1 in Rttyrite drop down menu Port
Selected TNC setup in Rttyrite drop down  menu TUType
Selected MMTTY setup
Under Tab AFC/ATC/PLL selected FSK
Under Tab Misc selected COM-TxD(FSK)
Closed screen then setup Icom 756 Pro II for RTTY mode and viola.
Keyboard works perfectly, perhaps better than before with AFSK.

Contacted W0SA on first try for a contact report was 599 and good print.
Signal was reported as clean.

So, I hope this may help other Rascal Interface users in the future who
connect to the ACC1 port on the IC-756PRO2.

Thanks again,

73, de Roland WA5CHX.

----- Original Message -----
From: "Bill Metzger" <wmetzger@earthlink.net>
To: "Roland Guidry - WA5CHX" <wa5chx@arrl.net>
Sent: Thursday, April 03, 2003 6:41 PM
Subject: Re: [WriteLog] FSK with Rascal inteface and 756Pro


> Roland,
>
> This is the exact setup that I use and have no problems.  In the Options
Tab
> for MMTTY Options (towards the bottom of the pull-down menu) there are
> several tabs.  Under AFC/ATC/PLL I have selected FSK, under the PTT tab, I
> use COM2 since this is the port the RASCAL is connected to, and finally
> under the Misc tab, under TX choose the COM-TxD(FSK).  Make sure you don't
> pick the one that starts with SOUND +.
>
> I had problems in the beginning also and finally found all these in the h
elpfiles.FSKworksgreat.BillKF0OH-----OriginalMessage-----FromRolandGuidry-WA
5CHXwa5chx@arrl.netTowritelog@contesting.zl6SentThursday,April03,2003507PMSu
bject[WriteLog]FSKwithRascalintefaceand756ProIhavebeenusingthe Rascal Mark V
Plus interface with an IC-756Pro2.
> Using
> > Writelog and MMTTY ins AFSK mode is no problem. I have followed
> instructions
> > for setting up to run FSK mode, by selecting the interface COM port and
> > selecting the different options under the Misc tab of MMTTY by selecting
> the
> > TU menu option. Although the transceiver keys up, it puts only a solid
> > signal tone out and the keyboard does work any of the commands the
> software.
> > Pressing ESC on the keyboard takes about 345 seconds for the shutdown to
> > occur.
> >
> > Does someone use the Rascal Mark V Plus interface with a IC-756? Can you
> > assist me in the setup. I am really stump. Bux CommCo can't help me with
> > writelog. Thanks in advance.
> >
> > Roland WA5CHX
> >
> >
> > _______________________________________________
> > WriteLog mailing list
> > WriteLog@contesting.com
> > http://lists.contesting.com/mailman/listinfo/writelog
>
>


<Prev in Thread] Current Thread [Next in Thread>