WriteLog
[Top] [All Lists]

Re: [WriteLog] MK2R+ and Writelog 11.18c

To: "Joe Subich, W4TV" <lists@subich.com>
Subject: Re: [WriteLog] MK2R+ and Writelog 11.18c
From: post@lb3re.com
Date: Tue, 20 May 2014 15:47:11 +0200
List-post: <writelog@contesting.com">mailto:writelog@contesting.com>
I just saw Radio 2 MMTTY RX window was silent when I toggle between RAdio
1 and 2.

I followed the Writelog setup.

So something must be totally wrong????

73 LB3RE


Den tir, mai 20, 2014, 15:37 skrev Joe Subich, W4TV:
>
> The example configuration is full of screen shots.
>
> 73,
>
>     ... Joe, W4TV
>
>
> On 2014-05-20 9:24 AM, LB3RE LJ3RE Stein-Roar Brobakken wrote:
>> If anyone can do printscreen of SO2r RTTY settings for MK2R+ in writelog
>> and urouter soundcard + mmtty I had been very happy I was little
>> confused by trying get it work too
>>
>> ---Sent by iphoneLB3RE LJ3RE K3RAG ex: LA6FJAwww.lb3re.com ~ Rag ~ Stein
>> Roar Brobakken e-mail:post@lb3re.com
>>
>> On 20. mai 2014 13:10:19 CEST, Richard Thorne <rthorne@rthorne.net>
>> wrote:         Group,  Thanks to Dean, Joe and Steve (GW4BLE) I
>> determined that I had to go into the windows sound system and select the
>> 2 channel option as described below.  Both instances of MMTTY are now
>> receiving the proper signal and demodulating correctly.  Now on to the
>> transmit issue which I'll tackle this evening.  I have a sneaking
>> suspicion that it has to do with the way I have my com ports setup.
>> I'll report back when I get it resolved.  After I get all of this
>> working, I'll look at installing OCX  Thanks  Rich - N5ZC     On
>> 5/19/2014 8:49 AM, Dean St. Hill wrote:   Rich    Welcome to the
>> twilight zone. Been there. Many times.     To see the way the sound
>> cards are set-up within your system - click on the Audio-switching tab
>> of MK2R+. then click on "soundcard" - over on the right 2/3 down the
>> window.     Even though the MMTTY plugin works, I would suggest that it
>> might be a good idea to actually use t
> he "OCX" set-up guideline as this is a more modern driver with the
> possibility of also using "2tone" as an alternative to MMTTY.     if
> you're setting audio from the left channel in both windows - 1st make sure
> the buttons on MK2R+ are set correctly. That's the top right section of
> MK2R. If that is correct then you need to go to windows sound system -
> right click on the "speaker logo" in the system tray. Choose recording
> devices. in the recording devices double-click the USB codec. Then choose
> "advanced" tab - extreme right top of the new window.  You will then see a
> drop-down with "default format" - this is where you need to choose a
> stereo option. Your current default is probably a mono option.     I
> choose 2 channel, 16 bit 44100Hz (CD Quality) and this has always worked
> for me but I am almost sure it can be a much much lower quality - others
> with more expertise may jump in and help with guidance here.     Finally
> after clicking the necessary "OK" etc. return to the two MMTTY wind
> ows and just confirm that left channel has been set up for your radio 1
> and right channel for your radio 2.      Hmmm... you may also want to go
> back to router as well and under audio switching tab re-confirm that the
> "use line out channel" has also been set for radio one and radio 2. both
> may be set as "left".     you should now be good to go as far as dual
> receive.     let's get that going and then check the tx side of the
> equation.     73 and best regards,      Dean - 8P6SH                On
> Mon, May 19, 2014 at 7:37 AM, Richard Thorne <rthorne@rthorne.net>
> wrote:This is a cross post to Writelog and Microham.  I've been working on
> configuring an MK2R+ SO2R controller with a pair of K3's and my Win 7 Pro
> computer.  I've been able to get SSB and CW to work properly.  I'm hung up
> on RTTY using MMTTY.  I've downloaded the setup guide from Microham and
> have setup two directories and two instances of MMTTY, I also have the
> MMTTY plug in for Writelog installed.  If I select the test butt
> on for FSK on the MK2R+ ports tab for rig 1 I get diddling same goes for
> rig 2.  While in Writelog I've followed the setup instructions by first
> selecting rig 1 and starting MMTTY from the appropriate directory, same
> for rig 2.  However, I can't get either to diddle.  In addition, both
> instances of MMTTY appear to be getting the same audio from rig 1 from the
> phone jack.  I've selected the right and left audio source on the misc tab
> while in TNC setup.  On the sound card tab in TNC setup I've selected
> Reception: Microphone (3 - USB Audio CODEC) and Transmission: Speakers (3
> - USB Audio CODEC)  How does one determine which device identifier to
> select on the misc tab in tnc setup?  I thought it would be 3 but I'm
> obviously incorrect.  I want to to use the line out on the rear of the
> K3's to grab the audio since it's fixed and won't be affected by the
> volume control of either K3.  The frustrating part is that I had this
> MK2R+ working just fine on RTTY with one K3, adding the 2nd K3 has
> been a challenge.  Is there an updated setup guide specifically for Win 7?
>  I'm half tempted to dust off an XP Pro laptop and give that a try, Win 7
> makes things very challenging.  Thanks in advance for any assistance.
> Rich - N5ZC      _______________________________________________ WriteLog
> mailing list WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog WriteLog on the web:
>  http://www.writelog.com/          --  Dean St.Hill      Counterpoint
> Consulting    17 Ocean City   St.Philip   Barbados       246-266-8230
> 246-416-5277       dmsthill@gmail.com                 __._,_.___    Posted
> by: Richard Thorne <rthorne@rthorne.net>        Reply via web post   •
> Reply to sender    •    Reply to group    •   Start a New Topic   •
> Messages in this topic (1)              This list is for the exchange of
> information about the use and operation of microHAM products.    Anyone
> with specific hardware support issues should contact microHAM support at
> mailto:suppor
> t@microHAM.com.       Visit Your Group   New Members 3          • Privacy
> • Unsubscribe • Terms of Use             .       __,_._,___
>> _______________________________________________
>> WriteLog mailing list
>> WriteLog@contesting.com
>> http://lists.contesting.com/mailman/listinfo/writelog
>> WriteLog on the web:  http://www.writelog.com/
>>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web:  http://www.writelog.com/
>


_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/
<Prev in Thread] Current Thread [Next in Thread>