Yaesu
[Top] [All Lists]

Re: [Yaesu] Problem in FT-101E -100v Circuit (Jerry Pittman)

To: "R_Davis" <WD8JJA@arrl.net>, <yaesu@contesting.com>
Subject: Re: [Yaesu] Problem in FT-101E -100v Circuit (Jerry Pittman)
From: "Jerry Pittman" <jerryp49@worldnet.att.net>
Reply-to: Jerry Pittman <jerryp49@worldnet.att.net>
Date: Sun, 15 Feb 2004 17:59:44 -0500
List-post: <mailto:yaesu@contesting.com>
Thanks for the tip Rick.  I checked that cap and it appears okay, so the
search goes on.
Jerry


----- Original Message ----- 
From: "R_Davis" <WD8JJA@arrl.net>
To: <yaesu@contesting.com>
Sent: Saturday, February 14, 2004 12:41 PM
Subject: [Yaesu] Problem in FT-101E -100v Circuit (Jerry Pittman)


> Check the coupling capacitor, C13, between the 12BY7A and the finals.
> Rick, WD8JJA.
>
> ----- Original Message -----
> From: <yaesu-request@contesting.com>
> To: <yaesu@contesting.com>
> Sent: Saturday, February 14, 2004 12:00 PM
> Subject: Yaesu Digest, Vol 14, Issue 9
>
>
> > Send Yaesu mailing list submissions to
> > yaesu@contesting.com
> >
> > To subscribe or unsubscribe via the World Wide Web, visit
> > http://lists.contesting.com/mailman/listinfo/yaesu
> > or, via email, send a message with subject or body 'help' to
> > yaesu-request@contesting.com
> >
> > You can reach the person managing the list at
> > yaesu-owner@contesting.com
> >
> > When replying, please edit your Subject line so it is more specific
> > than "Re: Contents of Yaesu digest..."
> >
> >
> > Today's Topics:
> >
> >    1. Problem in FT-101E -100v Circuit (Jerry Pittman)
> >
> >
> > ----------------------------------------------------------------------
> >
> > Date: Fri, 13 Feb 2004 12:41:26 -0500
> > From: "Jerry Pittman" <jerryp49@worldnet.att.net>
> > To: <yaesu@contesting.com>
> > Subject: [Yaesu] Problem in FT-101E -100v Circuit
> > Message-ID: <006e01c3f258$9b485ac0$6101a8c0@JerryPittman>
> > Content-Type: text/plain;
> > charset="iso-8859-1"
> > MIME-Version: 1.0
> > Content-Transfer-Encoding: quoted-printable
> > Precedence: list
> > Reply-To: Jerry Pittman <jerryp49@worldnet.att.net>
> > Message: 1
> >
> > Hello to all,
> > HELP!  I wonder if anyone has run into this problem:
> >
> > My 101E was just idling along while I was working on the computer the =
> > other evening, when I started smelling something hot.  I shot the rig =
> > off immediately and found that the bias control (VR1) on the voltage =
> > control board (PB1547B) had over heated, as well as the (2) 10K =
> > resistors on either side of the control.
> >
> > When I check the voltage at pin 5 of the 1547 board, I found that it was
=
> > getting -160v instead of -100v.  I went to the Rectifier board (PB1076B)
=
> > and made tests there.  When I disconnected the lead from the -100v =
> > terminal, the voltage shows -60v but with it is connected it shows =
> > -160v.  With the lead disconnected I also tested it for AC voltage and =
> > it shows 125vac as well as -60vdc.
> >
> > I checked all the components on the 1076B board and found all okay, but
=
> > just to be sure I hadn't missed something, I put in a used PB1076B board
=
> > and found all of the same readings.  I had already checked all of the =
> > other voltages coming and going from the 1076B and all are correct =
> > except the -100v.  The voltages from all of the transformer taps appear
=
> > to be within range as well.
> >
> > Does anyone have an Idea or run into this before?
> >
> > Thanks in advance for any responses.
> > Jerry
> > WD4OIX
> > jerryp49@att.net------------------------------
> >
> > _______________________________________________
> > Yaesu mailing list
> > Yaesu@contesting.com
> > http://lists.contesting.com/mailman/listinfo/yaesu
> >
> >
> > End of Yaesu Digest, Vol 14, Issue 9
> > ************************************
> >
>

_______________________________________________
Yaesu mailing list
Yaesu@contesting.com
http://lists.contesting.com/mailman/listinfo/yaesu

<Prev in Thread] Current Thread [Next in Thread>