Here’s how it’s done, Tom. As I said, it was very easy, no stress on the
control PCB, no cutting into the amp:
https://sites.google.com/site/k1jdalpha9500relayconversion/
73,
Jim w8zr
Sent from my iPad
On Nov 23, 2017, at 7:33 AM, Thomas Walsh <w2co@comcast.net> wrote:
Well that is interesting Jim, with the way the g41c's are mounted behind
the main ctrlr board, I don't see how any other
"fatter" relay could fit unless one cut a hole in the bulkhead. But that's
right smack into the tube deck area again allowing
out of phase rf into the cntrl board. Also the log amps and
the critical traces on that board which do all in/out fwd/ref wattmeter
functions, the log amps are sensitive and would need to be recalibrated at
the very least. If one put larger parts
there it would cause the board to bow when tightening down
the screws, and that's never good with a board with 100% smd
parts.. I would luv to find a replacement that would fit but it just
doesn't exist.
Tom W2CO
BTW, Happy TNXGVG to everyone!
Sent from my iPad
On Nov 23, 2017, at 07:15, MU 4CX250B <4cx250b@miamioh.edu> wrote:
Actually, they fit perfectly in the 9500, Tom, in the same location as the
originals. John K1JD and I made the swap in his 9500 one afternoon, because
he likes to run QSK and the Gigavac relays were too slow and noisy for him.
Jim W8ZR
Sent from my iPad
On Nov 23, 2017, at 6:41 AM, Thomas Walsh <w2co@comcast.net> wrote:
The only problem with using other relays is the fact that
they will not fit, the t/r relays in the 9500 are mounted
behind the main ctrlr board up against the bulkhead and
there's no room for any other type. If one tries to
mount relays anywhere else, wires would be required
the length of which will cause wattmeter calibration errors
as well as having the full output of the amp radiating who
knows where inside the amp. Not a good idea. There's a
reason they're mounted where they are.
A couple reasons they fail -1 high swr condx welds the
contacts closed, -2 lightning hits can also weld the contacts,
and -3 the op passed 1kw or more through in stby with high swr condx or not.
Tom
W2CO
Sent from my iPad
On Nov 23, 2017, at 05:55, MU 4CX250B <4cx250b@miamioh.edu> wrote:
Jennings RJ1A or the Kilovac HC1 relays are cheaper, widely available and
make (IMHO) a superior alternative to the G41C in the Alpha 9500. They are
about three times faster, have no contact bounce, and are much quieter.
They mount in grommets and can be swapped for the G41C relays in minutes,
without modifying the amplifier.
I’m curious about what happened to the original relays. What caused them to
fail?
73,
Jim w8zr
Sent from my iPhone
On Nov 23, 2017, at 4:31 AM, gudguyham--- via Amps <amps@contesting.com>
wrote:
Ouch!!
Sent from AOL Mobile Mail
On Thursday, November 23, 2017, Billy McDonald <bmm57@sbcglobal.net> wrote:
Had to buy two from Gigavac G41C from them and had to pay over $650.00 from
them NEW for a 9500
Billy Mac
AK5DX
-----Original Message-----
From: Amps [mailto:amps-bounces@contesting.com <amps-bounces@contesting.com>
<amps-bounces@contesting.com>]
On Behalf Of David B.
Ritchie
Sent: Wednesday, November 22, 2017 7:03 PM
To: amps@contesting.com
Cc: David B. Ritchie
Subject: [Amps] Alpha 9500 Relays Needed
Anybody have any Gigavac G41C Alpha 9500 relays lying around for sale?
Probably need one - would buy 2 new ones.
David W6DR
David B. Ritchie, Esq.
T: 650-862-6400
E: dbritchie@gmail.com
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|