Moin Peter,
Manche hier kenne die Deutsche Sprache. Ein paar Bilder von diese Multirohr
Enstufen sind auch Hoechstinteressant.
Tschuess, Dick
PA3DUV
----- Original Message -----
From: "Peter Voelpel" <df3kv@t-online.de>
To: <amps@contesting.com>
Sent: Tuesday, July 25, 2006 10:21 PM
Subject: Re: [Amps] Fw: "Tubes 201" - How Vacuum Tubes Really Work
> Will,
>
> It is also mentioned in my Siemens handbook of transmitting tubes together
> with the other safety measures on almost two pages.
> It is interesting to read that those measures were mandatory for claiming
> warranty replacement.
> I could scan that and put in on a website, but unfortunately it is in
> German
> only.
>
> 73
> Peter
>
> -----Original Message-----
> From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com] On
> Behalf Of Will Matney
>
>
> Exactly!!!!!
>
> That's the reason that if the grid is open, or floating, the tube turns
> into
> a diode and has no control of the electron flow. In effect, like you say,
> it
> would run away and eventually burn up. Way back when I first got into
> this,
> I said I never seen a problem with a grid fuse as long as the anode
> voltage
> was killed as soon as the fuse blew. One would never want to continue
> broadcasting after this condition happened. Since most amps monitor grid
> current, and plate voltage / current, it would be quickly seen on the
> meters
> if it happened. A trip could even be used to quash the B+ if this happened
> simply by watching the anode current. If it got too high, just kill the
> B+.
>
> I've not seen the Valvo article, but it would be a good read, and I'd
> personally like to see it.
>
> Thanks again,
>
> Will
>
> *********** REPLY SEPARATOR ***********
>
> On 7/25/06 at 9:24 PM Peter Voelpel wrote:
>
>>Hi Will,
>>
>>Yes, the grid must always keep its DC connection to ground not to turn
>>into
>>a runaway condition by a positive charged grid, it does not matter whether
>>it is grounded grid or grounded cathode circuitry.
>>For that reason VALVO suggested the 50KOhm safety resistor from grid to
>>ground in their transmitting tube manual when the grid is not strapped to
>>ground.
>>
>>73
>>Peter
>>
>>-----Original Message-----
>>From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com] On
>>Behalf Of Will Matney
>>Sent: Dienstag, 25. Juli 2006 20:52
>>To: amps@contesting.com
>>Subject: Re: [Amps] Fw: "Tubes 201" - How Vacuum Tubes Really Work
>>
>>Peter,
>>
>>Thanks! That is the very point I have been trying to get across all along!
>>Remember, the original threads were asking about a 3-500Z with the grid
>>resistor or fuse in G-G., or it was when I jumped in the mix There's been
>>a
>>lot of other tubes and circuits dragged into the discussion, but I've
>>tried
>>to center my comments around a 3-500Z G-G circuit. In grid driven circuits
>>though as in receivers and transmitters, or some amps, the grid can be
>>made
>>to go positive for part of a cycle. This I think Rich means also. He can
>>correct me if I'm wrong.
>>
>>Thanks,
>>
>>Will
>>
>>
>>*********** REPLY SEPARATOR ***********
>>
>>On 7/25/06 at 8:40 PM Peter Voelpel wrote:
>>
>>>Hi Will,
>>>
>>>when the grid is kept grounded it can not become more positive then the
>>>cathode if that is grounded and not negative biased as well, except by RF
>>>drive on it above its choke.
>>>
>>>73
>>>Peter
>>>
>>>-----Original Message-----
>>>From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com] On
>>>Behalf Of Will Matney
>>>
>>>Peter,
>>>
>>>On that, I agree it's the only way to make one positive (for only part of
>>a
>>>cycle). Are there any other ways to make the grid positive and the grid
>>>be
>>>at ground potential with the cathode at ground? A lot of amps cathodes
>>>are
>>>at ground potential unless biased.
>>>
>>>Best,
>>>
>>>Will
>>>
>>>
>>>
>>>*********** REPLY SEPARATOR ***********
>>>
>>>On 7/25/06 at 8:04 PM Peter Voelpel wrote:
>>>
>>>>Nothing is easier then that if the cathode is going/driven negative with
>>>>respect to ground.
>>>>Grid voltage is always measured from grid to cathode, not to ground.
>>>>
>>>>73
>>>>Peter
>>>>
>>>>
>>>>-----Original Message-----
>>>>From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com]
>>>>On
>>>>Behalf Of Will Matney
>>>>
>>>>please explain how a grid becomes positive when tied to ground?
>>>>
>>>>
>>>>
>>>>_______________________________________________
>>>>Amps mailing list
>>>>Amps@contesting.com
>>>>http://lists.contesting.com/mailman/listinfo/amps
>>>
>>>
>>>
>>>_______________________________________________
>>>Amps mailing list
>>>Amps@contesting.com
>>>http://lists.contesting.com/mailman/listinfo/amps
>>>
>>>_______________________________________________
>>>Amps mailing list
>>>Amps@contesting.com
>>>http://lists.contesting.com/mailman/listinfo/amps
>>
>>
>>
>>_______________________________________________
>>Amps mailing list
>>Amps@contesting.com
>>http://lists.contesting.com/mailman/listinfo/amps
>>
>>_______________________________________________
>>Amps mailing list
>>Amps@contesting.com
>>http://lists.contesting.com/mailman/listinfo/amps
>
>
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|